Bedienungsanleitung Pioneer AVIC-HD3 II (Seite 80 von 193) (Englisch)

491808

Zoom out

Zoom in

Vorherige Seite

1/193

Nächste Seite

The power voltage (reference value) pro-

vided from the vehicle battery to the naviga-

tion system is shown. If the voltage goes

out of the range from 11 V to 15 V, check

that power cable connection is correct.

7 Illumination

When the headlights or small lamps of a ve-

hicle are on, [On] is displayed. When the

small lamps of a vehicle are off, [Off] is dis-

played. (If the orange/white lead is not con-

nected, [Off] appears.)

8 Back Signal

When the gear lever is shifted to “R”, the

signal switches to [High]or[Low]. (One of

these is displayed depending on the vehi-

cle.)

Checking sensor learning

status and driving status

1 Touch [Settings] in the navigation

menu, then touch [Hardware].

2 Touch [3D Calibration Status].

The 3D Calibration Status screen appears.

1 Distance

Driving distance is indicated.

2 Speed Pulse

Total number of speed pulses is indicated.

3 Learning Status

Current driving mode is indicated.

4 Degree of learning

Sensor learning situations for distance

(Distance), right turn (Right Turn), left turn

(Left Turn) and 3D detection (3D Detec-

tion) are indicated by the length of bars.

p When tyres have been changed or

chains fitted, turning on the Speed

Pulse allows the system to detect the

fact that the tyre diameter has changed,

and automatically replaces the value for

calculating distance.

p If ND-PG1 is connected, the distance

calculation value cannot be replaced

automatically.

5 Speed

The speed detected by the navigation sys-

tem is indicated. (This indication may be

different from the actual speed of your vehi-

cle, so please do not use this instead of the

speedometer.)

6 Acceleration or deceleration/Rotational

speed

Acceleration or deceleration velocity of your

vehicle is indicated. Also, rotational speed

when your vehicle turns to left or right is

shown.

7 Inclination

Degree of slope of the street that you are

currently running is indicated.

To clear values...

If you want to delete the learned results stored

in [Distance], [Speed Pulse]or[Learning Sta-

tus], touch the relevant result, then touch

[Yes].

p If you select [Learning Status], you can se-

lect [Reset All]or[Reset Distance Study].

To clear all learning statuses, touch [Reset

All]. To clear only the Distance study, touch

[Reset Distance Study].

p Touch [Reset All] for the following cases:

— After changing the installation position

of the navigation system

— After changing the installation angle of

the navigation system

— After moving the navigation system to

another vehicle

p When the distance accuracy is low, touch

[Reset Distance Study].

p Touching [Reset All] returns the installa-

tion angle setting also to the default or fac-

tory setting. Reconfigure the setting.

Modifying the General Settings for Navigation Functions

Engb

Chapter

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer AVIC-HD3 II Seite 80

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer AVIC-HD3 II

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info