Bedienungsanleitung Pioneer avic x 1 (Seite 91 von 125) (Englisch)

162564

Zoom out

Zoom in

Vorherige Seite

1/125

Nächste Seite

Chapter 8 Customising the Audio Source SettingAV

Switching Auto PI Seek

The unit can automatically search for a different

station with the same programming, even during

preset recall.

1 Touch “AUTO PI” in the INITIAL menu.

Touching “AUTO PI” switches between “ON”

and “OFF”.

Switching the auxiliary setting

It is possible to use auxiliary equipment with nav-

igation unit. Activate the auxiliary setting when

using auxiliary equipment connected to naviga-

tion unit.

1 Touch “AUX” in the INITIAL menu.

Touching “AUX” switches between “ON” and

“OFF”.

Selecting the illumination col-

our

This unit is equipped with two illumination col-

ours, green and red. You can select the desired

illumination colour.

1 Touch “ILLUMI” in the INITIAL menu.

Touching “ILLUMI” switches between

“GREEN” (green) and “RED” (red).

Setting the rear output and sub-

woofer controller

This unit’s rear output (rear speaker leads output

and RCA rear output) can be used for full-range

speaker (REAR SP FULL) or subwoofer (REAR

SP SUB. W) connection. If you switch the rear

output setting to the REAR SP SUB. W, you can

connect a rear speaker lead directly to a sub-

woofer without using an auxiliary amp.

Initially, navigation unit is set for rear full-range

speaker connection (REAR SP FULL). When

rear output is connected to full range speakers

(when REAR SP FULL is selected), you can con-

nect the RCA subwoofer output to a subwoofer.

In this case, you can select whether to use the

subwoofer controller’s (low pass filter, phase)

built-in PREOUT SUB. W or the auxiliary

PREOUT FULL.

1 Touch “REAR SP” in the INITIAL menu.

2 Touch “REAR SP” to switch the rear out-

put setting.

When no subwoofer is connected to the rear

output, select FULL.

When a subwoofer is connected to the rear

output, select SUB. W.

❒ When the rear output setting is SUB. W,

you cannot change the subwoofer control-

ler.

3 Touch “PREOUT” to switch the sub-

woofer output or non fading output.

❒ Even if you change this setting, there is no

output unless you turn “NON FADING” or

“SUB WOOFER” in the AUDIO menu

“ON”.

➲ Using non fading output ➞ Page 85

➲ Using subwoofer output ➞ Page 85

❒ If you change the subwoofer controller

(REAR SP), the subwoofer output (SUB

WOOFER) and non fading output (NON

FADING) in the AUDIO menu return to

the factory settings.

❒ Both rear speaker leads output and RCA

rear output are switched simultaneously in

this setting.

Switching the sound muting/

attenuation

Sound from this system is muted, attenuated or

mixed automatically in the following cases:

• When a call is made or received using a cellu-

lar telephone connected to navigation unit.

• When the voice guidance is output.

1 Touch “TEL/GUIDE” in the INITIAL menu.

Each touch of the “TEL/GUIDE” changes the

settings as follows:

• MUTE — Muting

• ATT — Attenuation

• NORMAL — Volume does not change

❒ The sound is turned off, no audio adjust-

ment is possible.

❒ When a phone connection is made,

MUTE or ATT is indicated.

❒ Operation returns to normal when the

phone connection or the voice guidance is

ended.

Initial Settings

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer avic x 1 Seite 91

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer avic x 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info