Bedienungsanleitung Pioneer avic x 1 (Seite 109 von 125) (Englisch)

162564

109

Zoom out

Zoom in

Vorherige Seite

1/125

Nächste Seite

107

AppendixNAVI/AV

Your vehicle is operating in Simple

hybrid mode.

Connect the speed signal input (pink

lead wire) of the power cable cor-

rectly, and reset the 3D Hybrid Sen-

sor (“Learning Status”).

The navigation unit is installed with

an extreme angle exceeding the limi-

tation of the installation angle.

Confirm the installation angle. (This

unit must be installed within +30

degrees to –30 degrees of the hori-

zontal, or within five degrees of your

vehicle’s direction of travel.)

Indication of the position of your

vehicle is misaligned after a U-turn or

reversing.

Check whether or not the reverse

gear signal input lead (purple) is con-

nected properly. (The Navigation Sys-

tem works properly without the lead

connected, but positioning accuracy

will be adversely affected.)

The map continually reorients itself. The travelling direction is always set

to north.

Touch on the screen and change

the map display.

Tracking marks are not displayed. The “Tracking Display” is turned

off.

Check the “Tracking Display” set-

tings (

➞ Page 54) and make sure

“Always” or “This Trip” is selected.

The daylight display is used even

when the vehicle lights are on.

Daytime is selected on “Day/Night

Display”.

Check the “Day/Night Display” set-

ting (

➞ Page 54) and make sure

“Illuminated” is selected.

The Orange/white lead is not con-

nected.

Check the connection.

The system will not switch on or will

not operate.

Installation or connection has been

carried out incorrectly.

Check with your dealer.

The display is very dim. The vehicle’s light is turned ON, and

“Illuminated” is selected on “Day/

Night Display”.

Read about the “Day/Night Dis-

play” setting (

➞ Page 54) and, if

desired, select “Daytime”.

The vehicle cabin temperature is

extremely low.

A Liquid Crystal Display (LCD) is

used, and such displays tend to

darken when cold. Wait for the vehi-

cle to warm up.

Picture quality adjustment of the dis-

play is not correct.

Refer to “Hardware Manual” to

adjust the picture quality.

Ambient light sensor of the display is

hidden.

Set the ambient light sensor not to

be hidden.

There is no voice guidance or the vol-

ume is low.

The volume setting is low or the

speaker lead is disconnected.

Check the volume setting on the dis-

play or turn the volume up according

to “Hardware Volume” (

➞ Page 54)

and/or turn up the volume on the dis-

play.

Does not switch to Vehicle Dynam-

ics.

The navigation unit sensor does not

begin working immediately after the

navigation unit is installed on the

vehicle.

Drive for a little while.

Slope is not displayed on the

Vehicle Dynamics screen.

Inclination does not move on the

3D Calibration Status screen.

The speed pulse lead is not con-

nected.

Connect the speed pulse lead.

Symptom Cause Action (See)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer avic x 1 Seite 109

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer avic x 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info