Bedienungsanleitung Pioneer avic-x1bt (Seite 138 von 155) (Englisch)

162189

138

Zoom out

Zoom in

Vorherige Seite

1/155

Nächste Seite

136

Appendix NAVI/AV

Speed pulse wire is not connected.

Please be sure to connect the system

to the speed pulse wire. Accuracy is

not fully ensured without speed

pulse.

The speed signal input (pink lead

wire) of the power cable is not con-

nected.

To operate with 3D hybrid mode, con-

nect the speed signal input (pink

lead wire) of the power cable cor-

rectly.

Although it can be operated with

Simple hybrid mode without con-

necting the speed signal input, the

precision of the positioning will be

less accurate.

Vibration is detected. Please turn

system power off and check the

installation. After checking, please

re-boot the system and press “OK”.

The navigation system is installed in

a place where it may be affected by a

large vibration.

Re-install the Hide-away unit in a

place where the unit will not be

affected by vibration.

Direction of G sensor is not correct.

Please turn system power off and

check the installation. After check-

ing, please re-boot the system and

press “OK”.

Direction of G sensor is set incor-

rectly.

See the “Installation Manual” and set

the direction of the Hide-away unit

correctly.

Gyro Sensor is not working properly.

Please consult your dealer or Pioneer

service centre.

Abnormal output of Gyrosensor is

detected.

Note down the error code shown on

the screen; turn off the power, and

then contact your nearest Pioneer

service facility.

This function is not available now. The screen cannot be displayed with

Vehicle Dynamics Display.

Because the sensor has not been

taught so the sensor information

cannot be acquired.

If the sensor learning status reaches

the Sensor Initialising status or

more, the system is ready to be used.

System detected that the vertical

angle of the installation has been

changed. Learning status for Gyro

Sensor has been initialised.

If the mounting angle of the Hide-

away unit has been changed.

The system initialises the sensor in

order to operate it with the maximum

performance and automatically

starts re-learning.

System detected that the vertical

angle of the installation exceeds the

permission level. Please install the

navigation unit correctly.

The navigation system is installed

with an extreme angle exceeding the

limitation of the installation angle.

Confirm the installation angle. (The

navigation system must be installed

within +30 degrees to

–30 degrees

of the horizontal, or within five

degrees of your vehicle’s direction of

travel.)

Route calculation was not possible. Route calculation has failed because

of malfunction of map data, software,

hardware, or disc.

• Change the destination.

• Clean the disc.

• Consult the Pioneer Local dealer if

this message persists.

Route calculation was not possible

because the destination is too far.

The destination is too far. • Set a destination closer to the start-

ing point.

• Set one or more way points.

Route calculation was not possible

because the destination is too near.

The destination or way point(s) are

too close.

Set a destination [and way point(s)]

farther from the starting point.

Route calculation was not possible

due to traffic regulations.

• The destination or way point(s) are

in a Control Traffic Zone (CTR) and

the route calculation is hampered.

• Your vehicle is currently in a Con-

trol Traffic Zone (CTR) and the

route calculation is hampered.

• Set a destination and way point(s)

outside the CTR if you know where

the restricted area is.

• Try the destination or way point(s)

away from the currently set points

to some extent.

• Drive your vehicle to an unre-

stricted area and reset the destina-

tion and way point(s).

Route calculation was not possible

because no guidance can be pro-

vided around the destination or the

starting point.

The destination, way point(s), or

starting point are in an area where no

road exists (e.g. a mountain) and the

route calculation is impossible.

• Set a destination and way point(s)

on roads.

• Reset the destination after you

drive the vehicle to any road.

Message When What to do

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer avic-x1bt Seite 138

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer avic-x1bt

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info