Bedienungsanleitung Pioneer AVIC-X3 (Seite 115 von 164) (Englisch)

62771

115

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

113

Chapter 8 Customising the AV Source SettingAV

Initial Settings

Adjusting initial settings

Initial settings lets you perform initial set up of

different settings for navigation system.

(1) Function display

1 Touch “OFF” in the AV Source screen to

turn source off.

➲ “Selecting an AV source” ➞ Page 28

2 Press the MENU button to change to the

AV MENU.

3 Touch “Initial”.

Setting the FM tuning step

Normally the FM tuning step employed by seek

tuning is 50 kHz. When AF or TA is on, the tuning

step automatically changes to 100 kHz. It may be

preferable to set the tuning step to 50 kHz when

AF is on.

1 Touch “FM Step” in the Initial menu.

Each time you touch “FM Step” will switch

the FM tuning step between 50 kHz and 100

kHz while AF or TA is on.

❒ The tuning step remains at 50 kHz during

manual tuning.

Switching Auto PI seek

The unit can automatically search for a different

station with the same programming, even during

preset recall.

1 Touch “Auto PI” in the Initial menu.

Touching “Auto PI” switches between “On”

and “Off”.

Setting the rear output and sub-

woofer controller

This navigation system’s rear output (rear speaker

leads output and RCA rear output) can be used for

full-range speaker (

Rear SP

Full

) or subwoofer

(

Rear SP

Sub. W

) connection. If you switch the

rear output setting to the

Rear SP

Sub. W

, you

can connect a rear speaker lead directly to a sub-

woofer without using an auxiliary amp.

Initially, the navigation system is set for rear full-

range speaker connection (Rear SP Full). When

rear output is connected to full range speakers

(when Rear SP Full is selected), you can con-

nect the RCA subwoofer output to a subwoofer.

In this case, you can select whether to use the

subwoofer controller’s (low pass filter, phase)

built-in Preout Sub. W or the auxiliary Preout

Full.

1 Touch “Rear SP” in the Initial menu.

2 Touch “Rear SP” to switch the rear out-

put setting.

When no subwoofer is connected to the rear

output, select Full.

When a subwoofer is connected to the rear

output, select Sub. W.

❒ When the rear output setting is Sub. W,

you cannot change the subwoofer control-

ler.

3 Touch “Preout” to switch the subwoofer

output or non fading output.

❒ Even if you change this setting, there is no

output unless you turn “Non Fading” or

“Sub Woofer” in the Sound menu “On”.

➲ “Using non fading output” ➞ Page 109

➲ “Using subwoofer output” ➞ Page 109

❒ If you change the subwoofer controller

(Rear SP), the subwoofer output (Sub

Woofer) and non fading output (Non Fad-

ing) in the Sound menu return to the fac-

tory settings.

❒ Both rear speaker leads output and RCA

rear output are switched simultaneously in

this setting.

(1)

Initial Settings

MAN-AVIC-X3-EN.book Page 113 Wednesday, June 6, 2007 10:15 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer AVIC-X3 Seite 115

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer AVIC-X3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info