Bedienungsanleitung Pioneer AVIC-X850BT (Seite 155 von 204) (Englisch)

625516

155

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

CAUTION

! Thoroughly check the conditions before per-

forming Auto EQ, as the speakers may be da-

maged if this is performed under the following

conditions:

— When the speakers are incorrectly con-

nected. (For example, when a rear speaker

is connected as a subwoofer output.)

— When a speaker is connected to a power

amp delivering output higher than the

speaker’s maximum input power capabil-

ity.

! If a microphone for acoustical measurement

(sold separately) is not placed in an appropri-

ate location, the measurement tone may be-

come loud and measurement may take a long

time, resulting in battery drainage. Be sure to

place the microphone in the specified loca-

tion.

Before operating the Auto EQ

function

! Perform Auto EQ in as quiet a place as pos-

sible, with the vehicle engine and air condi-

tioning switched off. Also, cut power to car

phones or cellular phones in the vehicle, or

remove them from the vehicle before per-

forming Auto EQ. Sounds other than the

measurement tone (surrounding sounds,

engine sound, telephones ringing, etc.)

may prevent correct measurement of the

vehicle’s acoustics.

! Be sure to perform Auto EQ using the mi-

crophone for acoustical measurement

(sold separately). Using another micro-

phone may prevent measurement, or result

in incorrect measurement of the vehicle’s

acoustics.

! To perform Auto EQ, the front speakers

must be connected.

! When this navigation system is connected

to a power amp with input level control,

Auto EQ may be impossible if the power

amp’s input level is set below the standard

level.

! When this navigation system is connected

to a power amp with an LPF (low pass fil-

ter), turn the LPF off before performing

Auto EQ. Also, set the cut-off frequency for

the built-in LPF of an active subwoofer to

the highest frequency.

! The distance has been calculated by com-

puter to provide optimum delay to ensure

accurate results. Do not change this value.

— The reflected sound within the vehicle is

strong and delays occur.

— The LPF on active subwoofers or exter-

nal amps delay the lower sounds.

! If an error occurs during measurement, a

message appears and measurement is

canceled. Check the following before mea-

suring the vehicle’s acoustics.

— Front speakers (left/right)

— Rear speakers (left/right)

— Noise

— Microphone for acoustical measure-

ment (sold separately)

— Low battery

Performing Auto EQ

p Auto EQ changes the audio settings as fol-

lows:

! “Auto EQ” on the “EQ Menu” screen is

set to “On”.

= For details, refer to Using the auto-ad-

justed equalizer on page 153.

! The fader/balance settings return to the

center position.

= For details, refer to Using balance ad-

justment on page 150.

! The equalizer curve switches to “Flat”.

= For details, refer to Using the equali-

zer on page 151.

! The front and rear speakers will automa-

tically be adjusted to a high pass filter

setting.

p Previous settings for Auto EQ will be over-

written.

p For AVIC-Z150BH users

155

Chapter

Customizing preferences

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer AVIC-X850BT Seite 155

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info