Bedienungsanleitung Pioneer AVIC-Z140BH (Seite 186 von 240) (Englisch)

492010

186

Zoom out

Zoom in

Vorherige Seite

1/240

Nächste Seite

! Be sure to perform Auto EQ using the mi-

crophone for acoustical measurement

(sold separately). Using another micro-

phone may prevent measurement, or result

in incorrect measurement of the vehicle’s

acoustics.

! To perform Auto EQ, the front speakers

must be connected.

! When this navigation system is connected

to a power amp with input level control,

Auto EQ may not be able to be performed if

the power amp’s input level is set below

the standard level.

! When this navigation system is connected

to a power amp with an LPF, turn the LPF

off before performing Auto EQ. Also, set

the cut-off frequency for the built-in LPF of

an active subwoofer to the highest fre-

quency.

! The distance has been calculated by com-

puter to provide the optimum delay to en-

sure accurate results. Do not change this

value.

— The reflected sound within the vehicle is

strong and delays occur.

— The LPF on active subwoofers or exter-

nal amps delay the lower sounds.

! If an error occurs during measurement, a

message appears and measurement is

canceled. Check the following before mea-

suring the vehicle’s acoustics.

— Front speakers (left/right)

— Rear speakers (left/right)

— Noise

— Microphone for acoustical measure-

ment (sold separately)

— Low battery

Performing Auto EQ

p Auto EQ changes the audio settings as fol-

lows:

! “Auto EQ” on the “EQ Menu” screen is

set to “On”.

= For details, refer to Using the auto-ad-

justed equalizer on the previous

page.

! The fader/balance settings return to the

center position.

= For details, refer to Using balance ad-

justment on page 183.

! The equalizer curve switches to “Flat”.

= For details, refer to Using the equali-

zer on page 183.

! The front and rear speakers will automa-

tically be adjusted to a high pass filter

setting.

p Previous settings for Auto EQ will be over-

written.

p For AVIC-Z140BH users

Do not press the h button to open or close

the panel when you are using the micro-

phone.

1 Stop the vehicle in a place that is quiet,

close all the doors, windows and sun roof,

and then turn the engine off.

If the engine is left running, engine noise may

prevent correct Auto EQ.

p If driving restrictions are detected during

measurement, measurement is canceled.

2 Fix the microphone for acoustical mea-

surement (sold separately) in the center of

the headrest of the driver’s seat, facing for-

ward.

The Auto EQ may differ depending on where

you place the microphone. If desired, place

the microphone on the front passenger seat

and perform Auto EQ.

3 Turn the ignition switch to ON or ACC.

If the vehicle’s air conditioner or heater is

turned on, turn it off. Noise from the fan in the

air conditioner or heater may prevent correct

Auto EQ.

186

Chapter

Customizing preferences

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer AVIC-Z140BH Seite 186

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info