Bedienungsanleitung Pioneer AVIC-Z620BT (Seite 3 von 76) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

699597

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

3En

English

• Use this unit with a 12-volt battery and

negative earthing only. Failure to do so

may result in a fire or malfunction.

• To avoid shorts in the electrical system,

be sure to disconnect the (–) battery

cable before installation.

WARNING

• Use speakers over 50 W (maximum input

power) and between 4 Ω to 8 Ω

(impedance value). Do not use 1 Ω to 3 Ω

speakers for this product.

• The black lead is earth. Please earth this

lead separately from the earth of high

current products such as power amps. Do

not earth more than one product

together with the earth from another

product. For example, you must

separately earth any amp unit away from

the earth of this product. Connecting

earths together can cause a fire and/or

damage the products if their earths

became detached.

• When replacing the fuse, be sure to only

use a fuse of the rating prescribed on this

product.

• When disconnecting a connector, pull the

connector itself. Do not pull the lead, as

you may pull it out of the connector.

• This product cannot be installed in a

vehicle without ACC (accessory) position

on the ignition switch.

• To avoid short-circuiting, cover the

disconnected lead with insulating tape. It

is especially important to insulate all

unused speaker leads, which if left

uncovered may cause a short circuit.

• Attach the connectors of the same colour

to the corresponding coloured port, i.e.,

blue connector to the blue port, black to

black, etc.

• For connecting a power amp or other

devices to this product, refer to the

manual for the product to be connected.

• Since a unique BPTL circuit is employed,

do not directly earth the side of the

speaker lead or connect the side of

another side of the speaker lead together.

Be sure to connect the side of the

speaker lead to the side of the speaker

lead on this product.

• The graphical symbol placed on

the product means direct current.

• When the ignition switch is turned on

(ACC ON), a control signal is output

through the blue/white lead. Connect to

an external power amp’s system remote

control terminal, the auto-aerial relay

control terminal, or the aerial booster

power control terminal (max. 300 mA 12

V DC). The control signal is output

Before installing this

product

To prevent damage

Notice for the blue/

white lead

ACC position

No ACC position

through the blue/white lead, even if the

audio source is switched off.

• Be sure not to use this lead as the power

supply lead for the external power amps.

Such connection could cause excessive

current drain and malfunction.

• Be sure not to use this lead as the power

supply lead for the auto-aerial or aerial

booster. Such connection could cause

excessive current drain and malfunction.

Important

When this product is in [Power OFF] mode,

the control signal is also turned off. If

[Power OFF] mode is cancelled, the control

signal is output again and the aerial is

extended with the auto aerial function (if

the aerial is being used). Be careful so that

the extended aerial does not come into

contact with any obstacles.

WARNING

• To avoid the risk of accident and the

potential violation of applicable laws, this

product should never be used while the

vehicle is being driven except for

navigation purposes. And, also rear

displays should not be in a location

where it is a visible distraction to the

driver.

• In some countries, the viewing of images

on a display inside a vehicle even by

persons other than the driver may be

illegal. Where such regulations apply they

must be obeyed and this product’s video

source should not be used.

GPS aerial 3.55 m

Microphone 3 m

Vehicle Bus conversion cable 13 cm*.

Refer to the instruction manual for the

Vehicle Bus adapter (sold separately).

Digital Radio aerial input*

This product

Aerial jack

AV cable IN/OUT

Power supply

Fuse (10 A)

Wired remote input

Hard-wired remote control adapter can

be connected (sold separately).

*AVIC-Z920DAB/AVIC-Z820DAB/AVIC-

Z720DAB/AVIC-Z7210DAB

CAUTION

For improved Digital Radio reception,

make sure a Digital Radio aerial with

phantom power input (active type) is used.

Pioneer recommends using AN-DAB1 or

CA-AN-DAB.001 (sold separately). Current

consumption of the Digital Radio aerial

should be 100 mA or less.

WARNING

IMPROPER CONNECTION MAY RESULT IN

SERIOUS DAMAGE OR INJURY

Rear panel (main

terminals)

Power cord

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer AVIC-Z620BT Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer AVIC-Z620BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info