Bedienungsanleitung Pioneer AVIC_HD1BT (Seite 175 von 192) (Englisch)

25870

175

Zoom out

Zoom in

Vorherige Seite

1/192

Nächste Seite

173

AppendixNAVI/AV

The vertical installation angle is

changed. Gyro Sensor calibration is

re-initialized.

If the mounting angle of the naviga-

tion unit has been changed.

The system initialises the sensor in

order to operate it with the maximum

performance and automatically

starts re-learning.

Excess vertical installation angle

detected. Please install the naviga-

tion unit correctly.

The navigation system is installed

with an extreme angle exceeding the

limitation of the installation angle.

Confirm the installation angle. (The

navigation system must be installed

within the allowed installation angle.

For details, refer to Installation Man-

ual.)

Route calculation was not possible. Route calculation has failed because

of malfunction of map data, software,

hardware.

• Change the destination.

• Consult the Pioneer Local dealer if

this message persists.

Route calculation not possible

because destination is too far.

If the destination is too far. • Set a destination closer to the start-

ing point.

• Set one or more waypoints.

Route calculation not possible

because destination is too close.

The destination or waypoint(s) are

too close.

Set a destination and waypoint(s) far-

ther from the starting point.

Route calculation not possible due to

traffic regulations.

• The destination or waypoint(s) are

in a Control Traffic Zone (CTR) and

the route calculation is hampered.

• Your vehicle is currently in a Con-

trol Traffic Zone (CTR) and the

route calculation is hampered.

• Set a destination and waypoint(s)

outside the CTR if you know where

the restricted area is.

• Try the destination or waypoint(s)

away from the currently set points

to some extent.

• Drive your vehicle to an unre-

stricted area and reset the destina-

tion and waypoint(s).

Route calculation not possible

because navigation cannot be pro-

vided around destination or starting

point.

The destination, waypoint(s), or start-

ing point are in an area where no

road exists (e.g. a mountain) and the

route calculation is impossible.

• Set a destination and waypoint(s)

on roads.

• Reset the destination after you

drive the vehicle to any road.

Route to destination cannot be cal-

culated.

The destination or waypoint(s) are in

an isolated island, etc. without a ferry

and the route calculation is impossi-

ble. If there is no road connect to

your starting point or destination,

this message will appear.

Change the destination.

• Ferry could not be avoided.

• Toll roads could not be avoided.

• Motorway could not be avoided.

• Ferry, toll roads and motorways

could not be avoided.

• Ferry and toll roads could not be

avoided.

• Toll roads and motorways could not

be avoided.

• Ferry and motorway could not be

avoided.

In case a ferry route, toll roads or

motorways are included in the route

to the destination or waypoints even

though a route is set to avoid them.

You can recognise these condition by

icon.

➲ “Checking and modifying the

route” ➞ Page 24

If the current route is not desired, set

destination or waypoints that do not

pass through a ferry route, toll roads

or motorways.

This area does not contain any POI’s

of the selected type.

Facilities of the selected category do

not exist in the surrounding areas.

Use another search method or move

to another location and perform the

[Vicinity Search] again.

Failed to make the route profile. In rarely case the route calculation

error may occur.

•Retry.

• Consult the Pioneer Local dealer if

this message persists.

There is no Traffic List. There is no available traffic informa-

tion now.

Move to the location where you can

receive the RDS-TMC information,

and then try the operation again.

“Service provider name” is currently

unavailable.

The system cannot tune to the

selected provider for some reason.

• Select another provider.

• Move to the location where you can

receive the selected provider, and

then try the operation again.

Message When What to do

MAN-HD1BT-SOFTW-EN.book Page 173 Thursday, April 20, 2006 3:47 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer AVIC_HD1BT Seite 175

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer AVIC_HD1BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info