Bedienungsanleitung Pioneer CNDV-50MT (Seite 93 von 142) (Englisch)

454962

Zoom out

Zoom in

Vorherige Seite

1/142

Nächste Seite

Chapter 8 Customising the Audio Source SettingAV

Adjusting loudness

Loudness compensates for deficiencies in the

low- and high-sound ranges at low volume.

1 Touch “LOUDNESS” in the AUDIO menu.

2 Touch “ON” to turn loudness on.

To turn loudness off, touch “OFF”.

3 Touch 4 or 6 to select a desired level.

Each time you touch 4 or 6 selects level in

the following order:

LOW (low) – MID (mid) – HIGH (high)

Using subwoofer output

This unit is equipped with a subwoofer output

which can be turned on or off.

• When the subwoofer output is on, you can

adjust the cut-off frequency and the output

level of the subwoofer.

1 Touch “SUB WOOFER” in the AUDIO

menu.

When PREOUT (the subwoofer controller

setting in INITIAL menu) is FULL, you

cannot select “SUB WOOFER”.

➲ Rear speaker setting ➞ Page 95

2 Touch “ON” to turn subwoofer output on.

To turn subwoofer output off, touch “OFF”.

3 Touch “REVERSE” or “NORMAL” to

select the phase of subwoofer output.

4 Touch “+” or “–” to adjust the output

level of the subwoofer.

+6 – –6 is displayed as the level is increased

or decreased.

5 Touch 4 or 6 to select cut-off frequency.

Each time you touch 4 or 6 selects cut-off

frequencies in the following order:

50 – 80 – 125 (Hz)

Only frequencies lower than those in the

selected range are output from the subwoofer.

Using non fading output

When the non fading output setting is on, the

audio signal does not pass through navigation

unit’s low pass filter (for the subwoofer), but is

output through the RCA output.

1 Touch “NON FADING” in the AUDIO

menu.

Only when PREOUT (the subwoofer

controller setting in INITIAL menu) is FULL,

you can select “NON FADING”.

➲ Rear speaker setting ➞ Page 95

2 Touch “ON” to turn non fading output on.

To turn non fading output off, touch “OFF”.

3 Touch “+” or “–” to adjust the output

level of the non fading.

+6 – –6 is displayed as the level is increased

or decreased.

Using the high pass filter

When you do not want low sounds from the

subwoofer output frequency range to play from

the front or rear speakers, turn the HPF (high

pass filter) on. Only frequencies higher than

those in the selected range are output from the

front or rear speakers.

1 Touch “HPF” in the AUDIO menu.

2 Touch “ON” to turn high pass filter on.

To turn high pass filter off, touch “OFF”.

3 Touch 4 or 6 to select cut-off frequency.

Each time you touch 4 or 6 selects cut-off

frequencies in the following order:

50 – 80 – 125 (Hz)

When PREOUT (the subwoofer controller

setting in INITIAL menu) is SW, the HPF

function is effective for front speakers only.

Audio Adjustments

MAN-CNDV-50MT-EN.book Page 91 Wednesday, May 4, 2005 1:49 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer CNDV-50MT Seite 93

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer CNDV-50MT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info