454962

Pioneer CNDV-50MT Seite 123

123
Zoom out
Zoom in
Vorherige Seite
1/142
Nächste Seite
121
AppendixNAVI/AV
Direction of G sensor is not correct.
Please turn system power off and
check the installation. After
checking, please re-boot the system
and press “OK”.
Direction of G sensor is set
incorrectly.
See the “Installation Manual” and set
the direction of the Hide-away unit
correctly.
Gyro Sensor is not working properly.
Please consult your dealer or Pioneer
service centre.
Abnormal output of Gyrosensor is
detected.
Note down the error code shown on
the screen; turn off the power, and
then contact your nearest Pioneer
service facility.
This function is not available now. The screen cannot be displayed with
Vehicle Dynamics Display.
Because the sensor has not been
taught so the sensor information
cannot be acquired.
If the sensor learning status reaches
the Sensor Initialising status or
more, the system is ready to be used.
System detected that the vertical
angle of the installation has been
changed. Learning status for Gyro
Sensor has been initialised.
If the mounting angle of the Hide-
away unit has been changed.
The system initialises the sensor in
order to operate it with the maximum
performance and automatically
starts re-learning.
System detected that the vertical
angle of the installation exceeds the
permission level. Please install the
navigation unit correctly.
The navigation unit is installed with
an extreme angle exceeding the
limitation of the installation angle.
Confirm the installation angle. (The
navigation system must be installed
within +30 degrees to –30 degrees of
the horizontal, or within five degrees
of your vehicle’s direction of travel.)
Route calculation was not possible. Route calculation has failed because
of malfunction of map data, software,
hardware, or disc.
• Change the destination.
• Clean the disc.
• Consult the Pioneer Local dealer if
this message persists.
Route calculation was not possible
because the destination is too far.
The destination is too far. • Set a destination closer to the
starting point.
• Set one or more way points.
Route calculation was not possible
because the destination is too near.
The destination or way point(s) is too
close.
Set a destination [and way point(s)]
farther from the starting point.
Route calculation was not possible
due to traffic regulations.
• The destination or way point(s) are
in a Control Traffic Zone (CTR) and
the route calculation is hampered.
• Your vehicle is currently in a
Control Traffic Zone (CTR) and the
route calculation is hampered.
• Set a destination and way point(s)
outside the CTR if you know where
the restricted area is.
• Try the destination or way point(s)
away from the currently set points to
some extent.
• Drive your vehicle to an
unrestricted area and reset the
destination and way point(s).
Route calculation was not possible
because no guidance can be
provided around the destination or
the starting point.
The destination, way point(s), or
starting point are in an area where no
road exists (e.g. a mountain) and the
route calculation is impossible.
• Set a destination and way point(s)
on roads.
• Reset the destination after you
drive the vehicle to any road.
There is no route to the destination. The destination or way point(s) are in
an isolated island, etc. without a ferry
and the route calculation is
impossible.
Change the destination.
Your journey can not avoid the
specified area.
If route setting cannot avoid
specified Areas to Avoid.
If the current route is not desired, set
destination or way points that do not
pass through the Areas to Avoid.
The route could not avoid the
specified area.
Toll road has not been avoided.
If the route to the destination (or way
point) cannot be established by
bypassing toll roads (including toll
areas) and Areas to Avoid.
If the current route is not desired, set
destination or way points that do not
pass through toll roads (including
toll areas) and Areas to Avoid.
Ferry has not been avoided. In case a ferry route was included in
the route to the destination or way
points even though “Avoid Ferry”
was set to On.
If the current route is not desired, set
destination or way points that do not
pass through a ferry route.
Message When What to do
MAN-CNDV-50MT-EN.book Page 121 Wednesday, May 4, 2005 1:49 PM
… 123 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Pioneer CNDV-50MT wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Pioneer CNDV-50MT

Pioneer CNDV-50MT Bedienungsanleitung - Holländisch - 152 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info