507727
1
Zoom out
Zoom in
Vorherige Seite
1/8
Nächste Seite
<KOKZX>  <08H00000>
Printed in Thailand 
Imprimé en Thaïlande
<QRD3015-A/N> EW
Installation Manual
Manual de instalación
Installationsanleitung
Manuel d’installation
Manuale d’installazione
Installatiehandleiding
Руководство по установке
CD RDS RECEIVER
REPRODUCTOR DE CD CON RECEPTOR RDS
CD RDS-EMPFÄNGER
AUTORADIO CD RDS
SINTOLETTORE CD RDS
CD RDS-ONTVANGER
CD RDS ПРИЕМНИК
DEH-1120MP
DEH-1100MPB
DEH-1100MP
DEH-112E
DEH-110E
<QRD3015-A> 1
Important
! Check all connections and systems before
final installation.
! Do not use unauthorized parts. Use of un-
authorized parts may cause malfunctions.
! Consult your dealer if installation requires dril-
ling of holes or other modifications to the vehi-
cle.
! Do not install this unit where :
it may interfere with operation of the vehi-
cle.
it may cause injury to a passenger as a re-
sult of a sudden stop.
! The semiconductor laser will be damaged if it
overheats. Install this unit away from hot
places such as near the heater outlet.
! Optimum performance is obtained when the
unit is installed at an angle of less than 60°.
60°
DIN front/rear mount
This unit can be properly installed either from
Front (conventional DIN front-mount) or
Rear (DIN rear-mount installation, utilizing
threaded screw holes at the sides of unit chas-
sis). For details, refer to the following installa-
tion methods.
DIN Front-mount
Installation with the rubber bush
1 Insert the mounting sleeve into the
dashboard.
When installing in a shallow space, use a sup-
plied mounting sleeve. If there is enough
space behind the unit, use factory supplied
mounting sleeve.
2 Secure the mounting sleeve by using a
screwdriver to bend the metal tabs (90°)
into place.
3 Install the unit.
Dashboard Rubber bush
Mounting sleeve Screw
Removing the unit
1 Extend top and bottom of the trim ring
outwards to remove the trim ring. (When
reattaching the trim ring, point the side
with a groove downwards and attach it.)
Trim ring
! It becomes easy to remove the trim ring if
the front panel is released.
2 Insert the supplied extraction keys into
both sides of the unit until they click into
place.
3 Pull the unit out of the dashboard.
Installation
En
<QRD3015-A> 2
DIN Rear-mount
1 Extend top and bottom of the trim ring
outwards to remove the trim ring. (When
reattaching the trim ring, point the side
with a groove downwards and attach it.)
Trim ring
! It becomes easy to remove the trim ring if
the front panel is released.
2 Determine the appropriate position
where the holes on the bracket and the
side of the unit match.
3 Tighten two screws on each side.
Screw
Mounting bracket Dashboard or console
! Use either truss screws (5 mm × 8 mm) or
flush surface screws (5 mm × 9 mm), de-
pending on the shape of screw holes in the
bracket.
Fastening the front panel
If you do not plan to detach the front panel,
the front panel can be fastened with supplied
screw.
Screw
Installation
En
<QRD3015-A> 3
<QRD3015-A> 4
Importante
! Compruebe todas las conexiones y sistemas
antes de la instalación final.
! No utilice piezas no autorizadas. El uso de pie-
zas no autorizadas puede causar fallos de fun-
cionamiento.
! Consulte a su concesionario si para la instala-
ción es necesario taladrar orificios o hacer
otras modificaciones al vehículo.
! No instale esta unidad en un lugar donde:
pueda interferir con la conducción del ve-
hículo.
pueda lesionar a un pasajero como conse-
cuencia de un frenazo brusco.
! El láser semiconductor se dañará si se sobre-
calienta. Instale esta unidad alejada de zonas
que alcancen altas temperaturas, como cerca
de la salida del calefactor.
! Se logra un rendimiento óptimo si la unidad
se instala en un ángulo inferior a 60°.
60°
Montaje delantero/
posterior DIN
Esta unidad se puede instalar adecuadamente
ya sea de manera delantera (montaje delan-
tero convencional DIN) o posterior (instala-
ción de montaje posterior DIN, utilizando
agujeros roscados para tornillos en los latera-
les del bastidor de la unidad). Para obtener de-
talles, consulte los siguientes métodos de
instalación.
Montaje delantero DIN
Instalación en la arandela de goma
1 Inserte el manguito de montaje en el
salpicadero.
Si realiza la instalación en un espacio poco
profundo, utilice un manguito de montaje su-
ministrado. Si hay suficiente espacio detrás de
la unidad, utilice un manguito de montaje su-
ministrado de fábrica.
2 Fije el manguito de montaje utilizando
un destornillador para doblar las pestañas
metálicas (90°) y colocarlas en su lugar.
3 Instale la unidad.
Salpicadero Arandela de goma
Manguito de montaje Tornillo
Retirada de la unidad
1 Extienda hacia afuera la parte superior
e inferior del aro de guarnición para retirar-
lo. (Al volver a colocar el anillo de guarni-
ción, oriente el lado que tiene una ranura
hacia abajo y colóquelo.)
Anillo de guarnición
! Resulta más fácil retirar el anillo de guarni-
ción si se suelta la carátula.
Instalación
Es
<QRD3015-A> 5
2 Inserte en ambos lados de la unidad las
llaves de extracción provistas hasta que se
escuche un ligero chasquido.
3 Extraiga la unidad del salpicadero.
Montaje trasero DIN
1 Extienda hacia afuera la parte superior
e inferior del aro de guarnición para retirar-
lo. (Al volver a colocar el anillo de guarni-
ción, oriente el lado que tiene una ranura
hacia abajo y colóquelo.)
Anillo de guarnición
! Resulta más fácil retirar el anillo de guarni-
ción si se suelta la carátula.
2 Determine la posición correcta, de
modo que los orificios del soporte y del la-
teral de la unidad coincidan.
3 Apriete los dos tornillos en cada lado.
Tornillo
Carcasa Salpicadero o consola
! Utilice tornillos de cabeza redonda (5 mm
× 8 mm) o tornillos de cabeza embutida (5
mm × 9 mm), según la forma de los orifi-
cios roscados del soporte.
Fijación de la carátula
Si no tiene previsto sacar la carátula, ésta se
puede fijar con el tornillo suministrado.
Tornillo
Instalación
Es
<QRD3015-A> 6
Wichtig
! Überprüfen Sie vor der definitiven Installation
alle Anschlüsse und Systeme.
! Verwenden Sie ausschließlich autorisierte
Teile. Die Verwendung nicht autorisierter Teile
kann eine Funktionsstörung zur Folge haben.
! Wenden Sie sich an Ihren Fachhändler, wenn
für die Installation Löcher gebohrt oder ande-
re Änderungen am Fahrzeug vorgenommen
werden müssen.
! Installieren Sie dieses Gerät keinesfalls an fol-
genden Orten:
Orte, an denen das Gerät die Steuerung
des Fahrzeugs behindern könnte.
Orte, an denen das Gerät die Insassen des
Fahrzeugs im Anschluss an eine Schnell-
bremsung verletzen könnte.
! Der Halbleiterlaser kann durch Überhitzung
beschädigt werden. Installieren Sie dieses
Gerät deshalb in sicherer Entfernung von Hit-
zequellen, wie z. B. Heizöffnungen.
! Optimale Leistung kann durch eine Installa-
tion des Geräts in einem Winkel unter 60° er-
zielt werden.
60°
Front-/Rückmontage nach DIN
Dieses Gerät kann sowohl über die Frontseite
(herkömmliche DIN-Frontmontage) als auch
über die Rückseite (DIN-Rückmontage unter
Rückgriff auf die Gewindelöcher an den Seiten
des Gerätegehäuses) installiert werden. Detail-
lierte Informationen können Sie den nachste-
henden Beschreibungen dieser
Installationsmethoden entnehmen.
DIN-Frontmontage
Installation mit Gummilager
1 Führen Sie den Montagerahmen in das
Armaturenbrett ein.
Bei nur wenig Installationsraum ist der mitge-
lieferte Montagerahmen zu verwenden. Ist hin-
ter dem Gerät ausreichend Freiraum
vorhanden, dann sollten Sie den werkseitig be-
reitgestellten Montagerahmen verwenden.
2 Befestigen Sie den Montagerahmen
mithilfe eines Schraubendrehers: Die Me-
tallklammern sind in eine sichere Position
(90°) zu biegen.
3 Installieren Sie dieses Gerät.
Armaturenbrett Gummilager
Montagerahmen Schraube
Entfernen des Geräts
1 Ziehen Sie den Einpassungsring oben
und unten nach außen, um ihn zu entfer-
nen. (Um den Einpassungsring wieder an-
zubringen, drücken Sie die Seite mit der
Nute nach unten und befestigen Sie sie.)
Einpassungsring
! Bei entriegelter Frontplatte lässt sich der
Einpassungsring problemlos entfernen.
Installation
De
<QRD3015-A> 7
2 Führen Sie die mitgelieferten Extrakti-
onsschlüssel an beiden Geräteseiten ein,
bis sie in der richtigen Position einrasten.
3 Ziehen Sie das Gerät aus dem Armatur-
enbrett.
DIN-Rückmontage
1 Ziehen Sie den Einpassungsring oben
und unten nach außen, um ihn zu entfer-
nen. (Um den Einpassungsring wieder an-
zubringen, drücken Sie die Seite mit der
Nute nach unten und befestigen Sie sie.)
Einpassungsring
! Bei entriegelter Frontplatte lässt sich der
Einpassungsring problemlos entfernen.
2 Bestimmen Sie die geeignete Position,
damit die Löcher an der Klammer und den
Geräteseiten ordnungsgemäß ausgerichtet
sind.
3 Ziehen Sie auf jeder Seite zwei Schrau-
ben fest.
Schraube
Montageklammer Armaturenbrett oder Kon-
sole
! Verwenden Sie entweder Trägerschrauben
(5 mm × 8 mm) oder Oberflächenschrau-
ben (5 mm × 9 mm), je nach der Form der
Gewindelöcher in der Klammer.
Anbringen der Frontplatte
Wenn Sie nicht vorhaben, die Frontplatte abzu-
nehmen, kann diese auch mittels der beige-
fügten Schrauben permanent angebracht
werden.
Schraube
Installation
De
<QRD3015-A> 8
1*
2*3*
4*5*
1 This product
2 Antenna jack
3 Fuse (10 A)
4 Note:
Depending on the kind of vehicle, the function
of 3* and 5* may be different. In this case, be
sure to connect 2* to 5* and 4* to 3*.
5 Connect leads of the same
color to each other.
6 Cap (1*)
Do not remove cap if this
terminal is not in use.
7 Yellow (3*)
Back-up
(or accessory)
8 Yellow (2*)
Connect to the constant 12 V supply
terminal.
9 Red (5*)
Accessory
(or back-up)
10 Red (4*)
Connect to terminal controlled by
ignition switch (12 V DC).
11 Black (chassis ground)
Connect to a clean, paint-free metal location.
12 ISO connector
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to
connect to both connectors.
13 Speaker leads
White: Front left
White/black: Front left
Gray: Front right
Gray/black: Front right
Green: Rear left
Green/black: Rear left
Violet: Rear right
Violet/black: Rear right
19 Rear output
(DEH-1120MP/DEH-1100MPB/
DEH-1100MP)
Connections
En
<QRD3015-A> 17
Fig. 1
Abb. 1
Afb. 1
Рис. 1
16 Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
17 Blue/white (7*)
Connect to auto-antenna relay control
terminal (max. 300 mA 12 V DC).
18 Blue/white (6*)
The pin position of the ISO connector will
differ depends on the type of vehicle.
Connect 6* and 7* when Pin 5 is an
antenna control type. In another type of
vehicle, never connect 6* and 7*.
14 Wired remote input
Hard-wired remote control adaptor
can be connected (sold separately).
15 Yellow/black
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead
free of any connections.
20 This diaglam is for DEH-1120MP/DEH-1100MPB/DEH-1100MP.
22 Connect with RCA cables
(sold separately)
23 Power amp
(sold separately)
24 System remote control
26 Right25 Left
27 Rear speaker 27 Rear speaker
28 Perform these connections when using
the optional amplifier.
21 To Rear output
Connections
En
<QRD3015-A> 18
Important
! When this unit is installed in a vehicle without
ACC (accessory) position on the ignition
switch, red cable must be wired to the term-
inal that can detect the operation of the igni-
tion key. Otherwise, battery drain may result.
O
N
S
T
A
R
T
O
F
F
ACC position No ACC position
! Use of this unit in conditions other than the
following could result in fire or malfunction.
Vehicles with a 12-volt battery and negative
grounding.
Speakers with 50 W (output value) and 4
ohm to 8 ohm (impedance value).
! To prevent a short-circuit, overheating or mal-
function, be sure to follow the directions
below.
Disconnect the negative terminal of the
battery before installation.
Secure the wiring with cable clamps or ad-
hesive tape. To protect the wiring, wrap ad-
hesive tape around them where they lie
against metal parts.
Place all cables away from moving parts,
such as gear shift and seat rails.
Place all cables away from hot places,
such as near the heater outlet.
Do not pass the yellow cable through a
hole into the engine compartment to con-
nect to a battery.
Cover any disconnected cable connectors
with insulating tape.
Do not shorten any cables.
Never cut the insulation of the power cable
of this unit in order to share the power
with other devices. Current capacity of the
cable is limited.
Use a fuse of the rating prescribed.
Never wire the speaker negative cable di-
rectly to ground.
Never band together multiple speakers ne-
gative cables.
! Control signal is output through blue/white
cable when this unit is powered on. Connect it
to an external power amps system remote
control or the vehicles auto-antenna relay
control terminal (max. 300 mA 12 V DC). If the
vehicle is equipped with a glass antenna, con-
nect it to the antenna booster power supply
terminal.
! Never connect blue/white cable to external
power amps power terminal. Also, never con-
nect it to the power terminal of the auto anten-
na. Otherwise, battery drain or malfunction
may result.
! Black cable is ground. This cable and other
products ground cable (especially, high-cur-
rent products such as power amp) must be
wired separately. Otherwise, fire or malfunc-
tion may result if they are accidentally de-
tached.
Connection Diagram (Fig. 1)
1 This product
2 Antenna jack
3 Fuse (10 A)
4 Note:
Depending on the kind of vehicle, the function
of 3* and 5* may be different. In this case, be
sure to connect 2* to 5* and 4* to 3*.
5 Connect leads of the same color to each
other.
6 Cap (1*)
Do not remove cap if this terminal is not in
use.
7 Yellow (3*)
Back-up (or accessory)
8 Yellow (2*)
Connect to the constant 12 V supply terminal.
9 Red (5*)
Accessory (or back-up)
Connections
En
<QRD3015-A> 19
10 Red (4*)
Connect to terminal controlled by ignition
switch (12 V DC).
11 Black (chassis ground)
Connect to a clean, paint-free metal location.
12 ISO connector
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to con-
nect to both connectors.
13 Speaker leads
White: Front left +
White/black: Front left *
Gray: Front right +
Gray/black: Front right *
Green: Rear left +
Green/black: Rear left *
Violet: Rear right +
Violet/black: Rear right *
14 Wired remote input
Hard-wired remote control adaptor can be
connected (sold separately).
15 Yellow/black
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead
free of any connections.
16 Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
17 Blue/white (7*)
Connect to auto-antenna relay control term-
inal (max. 300 mA 12 V DC).
18 Blue/white (6*)
The pin position of the ISO connector will dif-
fer depends on the type of vehicle. Connect 6*
and 7* when Pin 5 is an antenna control type.
In another type of vehicle, never connect 6*
and 7*.
19 Rear output (DEH-1120MP/DEH-1100MPB/
DEH-1100MP)
20 This diagram is for DEH-1120MP/DEH-
1100MPB/DEH-1100MP.
21 To Rear output
22 Connect with RCA cables (sold separately)
23 Power amp (sold separately)
24 System remote control
25 Left
26 Right
27 Rear speaker
28 Perform these connections when using the
optional amplifier.
Connections
En
<QRD3015-A> 20
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Pioneer DEH-112E wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Pioneer DEH-112E

Pioneer DEH-112E Bedienungsanleitung - Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Spanisch - 107 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info