Bedienungsanleitung Pioneer DEH-2600UI (Seite 13 von 148) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

528322

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

Black plate (13,1)

Power amp (sold separately)

Perform these connections when using the op-

tional amplifier.

















1 System remote control

Connect to Blue/white cable.

2 Power amp (sold separately)

3 Connect with RCA cables (sold separately)

4 To Front output

5 Front speaker

6 To Rear output or subwoofer output

7 Rear speaker or subwoofer

Installation

Important

! Check all connections and systems before

final installation.

! Do not use unauthorized parts as this may

cause malfunctions.

! Consult your dealer if installation requires

drilling of holes or other modifications to the

vehicle.

! Do not install this unit where:

— it may interfere with operation of the vehicle.

— it may cause injury to a passenger as a result

of a sudden stop.

! The semiconductor laser will be damaged if

it overheats. Install this unit away from hot

places such as near the heater outlet.

! Optimum performance is obtained when the

unit is installed at an angle of less than 60°.

60°

! When installing, to ensure proper heat dis-

persal when using this unit, make sure you

leave ample space behind the rear panel and

wrap any loose cables so they are not block-

ing the vents.

5cmcm

Leave ample

space

5 cm

DIN front/rear mount

This unit can be properly installed using either

front-mount or rear-mount installation.

Use commercially available parts when instal-

ling.

DIN Front-mount

1 Insert the mounting sleeve into the dash-

board.

For installation in shallow spaces, use the sup-

plied mounting sleeve. If there is enough space,

use the mounting sleeve that came with the ve-

hicle.

2 Secure the mounting sleeve by using a

screwdriver to bend the metal tabs (90°) into

place.

1 Dashboard

2 Mounting sleeve

# Make sure that the unit is installed securely in

place. An unstable installation may cause skipping

or other malfunctions.

DIN Rear-mount

1 Determine the appropriate position

where the holes on the bracket and the side

of the unit match.

2 Tighten two screws on each side.

1 Tapping screw (5 mm × 8 mm)

2 Mounting bracket

3 Dashboard or console

Removing the unit

1 Remove the trim ring.

1 Trim ring

2 Notched tab

! Releasing the front panel allows easier ac-

cess to the trim ring.

! When reattaching the trim ring, point the

side with the notched tab down.

2 Insert the supplied extraction keys into

both sides of the unit until they click into

place.

3 Pull the unit out of the dashboard.

Removing and re-attaching the front

panel

You can remove the front panel to protect your

unit from theft.

For details, refer to Removing the front panel and

Re-attaching the front panel on page 4.

English

Installation

Section

Installation

<QRD3200-A>13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer DEH-2600UI Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info