Bedienungsanleitung Pioneer DEH-80PRS (Seite 4 von 44) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

491827

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

WARNING

Do not use the unit in standard mode when a

speaker system for 3-way network mode is con-

nected to this unit. This may cause damage to

the speakers.

1 Use a thin, flathead screwdriver to

change the DSP switch on the bottom of this

unit.

2 Press RESET with a pen tip or other

pointed instrument.

For details, refer to the operation manual.

Audio input

If you connect the unit to an audio device with

RCA output, or to one with no RCA output, you

can set it up so that the audio from the audio de-

vice is output through speakers connected to

the unit. Change settings as necessary based on

whether the connected device has RCA output

or not.

For more details on change settings, refer to the

operation manual or Switching between RCA

input modes on this page.

If connecting the unit to a car

stereo with RCA output

23 4

1 Car stereo with RCA output

2 To audio output

3 Connect with RCA cable (sold separately)

4 To audio input

If connecting the unit to a car

stereo with no RCA output

1 Car stereo with no RCA output

2 To speaker output

3 Red: Right +

4 Black: Right *

5 Black: Left *

6 White: Left +

7 Speaker-RCA conversion cable (supplied)

19 cm

8 To audio input

Switching between RCA input

modes

% Use a thin, flathead screwdriver to

change the RCA input mode switch on the

bottom of this unit.

! L (Low) - If inputting from the RCA output of a

connected device

! H (High) - If inputting from the speaker out-

put of a connected device

Important

! Check all connections and systems before

final installation.

! Do not use unauthorized parts as this may

cause malfunctions.

! Consult your dealer if installation requires

drilling of holes or other modifications to the

vehicle.

! Do not install this unit where:

— it may interfere with operation of the vehicle.

— it may cause injury to a passenger as a result

of a sudden stop.

! The semiconductor laser will be damaged if

it overheats. Install this unit away from hot

places such as near the heater outlet.

! Optimum performance is obtained when the

unit is installed at an angle of less than 60°.

60°

! When installing, to ensure proper heat dis-

persal when using this unit, make sure you

leave ample space behind the rear panel and

wrap any loose cables so they are not block-

ing the vents.

5cmcm

Leave ample

space

5 cm

DIN front/rear mount

This unit can be properly installed using either

front-mount or rear-mount installation.

Use commercially available parts when instal-

ling.

DIN Front-mount

1 Insert the mounting sleeve into the dash-

board.

For installation in shallow spaces, use the sup-

plied mounting sleeve. If there is enough space,

use the mounting sleeve that came with the ve-

hicle.

2 Secure the mounting sleeve by using a

screwdriver to bend the metal tabs (90°) into

place.

1 Dashboard

2 Mounting sleeve

3 Install the unit as illustrated.

1 Nut

2 Firewall or metal support

3 Metal strap

4 Screw

5 Screw (M4 × 8)

Connections

Section

Installation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer DEH-80PRS Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer DEH-80PRS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info