Bedienungsanleitung Pioneer deh p5500mp (Seite 56 von 65) (Englisch)

167026

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

DIN Rear-mount

Installation using the screw holes on the side of the unit

1. Remove the frame. (Fig. 8)

Fig. 8

2. Fastening the unit to the factory radio mounting bracket.

(Fig. 9) (Fig. 10)

Select a position where the screw holes of the bracket and

the screw holes of the head unit become aligned (are fitted),

and tighten the screws at 2 places on each side. Use either

truss screws (5 × 8 mm) or flush surface screws

(5 × 9 mm), depending on the shape of the screw holes in

the bracket.

Fig. 9

Fig. 10

Frame

Insert the release pin into the hole in

the bottom of the frame and pull out

to remove the frame.

(When reattaching the frame, point

the side with a groove downwards

and attach it.)

Installation <ENGLISH>

Screw

Dashboard or Console

Factory radio mounting bracket

Note:

• Before finally installing the unit, connect the

wiring temporarily, making sure it is all connected

up properly, and the unit and the system work

properly.

• Use only the parts included with the unit to ensure

proper installation. The use of unauthorized parts

can cause malfunctions.

• Consult with your nearest dealer if installation

requires the drilling of holes or other modifications

of the vehicle.

• Install the unit where it does not get in the driver’s

way and cannot injure the passenger if there is a

sudden stop, like an emergency stop.

• The semiconductor laser will be damaged if it

overheats, so don’t install the unit anywhere hot —

for instance, near a heater outlet.

• If installation angle exceeds 60° from horizontal,

the unit might not give its optimum performance.

(Fig. 4)

Fig. 4

60°

DIN Front/Rear-mount

This unit can be properly installed either from “Front” (conventional DIN Front-mount) or

“Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit

chassis). For details, refer to the following illustrated installation methods.

DIN Front-mount

Installation with the rubber bush (Fig. 5)

Fig. 5

182

Dashboard

Rubber bush

Screw

Holder

After inserting the holder into the

dashboard, then select the appropriate

tabs according to the thickness of the

dashboard material and bend them.

(Install as firmly as possible using the

top and bottom tabs. To secure, bend

the tabs 90 degrees.)

Removing the unit (Fig. 6) (Fig. 7)

Fig. 6

Fig. 7

Insert the release pin into the hole in

the bottom of the frame and pull out

to remove the frame.

(When reattaching the frame, point

the side with a groove downwards

and attach it.)

Frame

Insert the supplied extraction keys

into the unit, as shown in the figure,

until they click into place. Keeping

the keys pressed against the sides of

the unit, pull the unit out.

Fixing the front panel

If you do not operate the removing and attaching the front panel function, use the supplied

fixing screws and holders to fix the front panel to this unit.

1. Attach the holders to both sides of the front panel. (Fig. 11)

Fig. 11

2. Replace the front panel to the unit. (Fig. 12)

Fig. 12

Flip the holders into upright positions.

(Fig. 13)

Fig. 13

4. Fix the front panel to the unit using fixing screws. (Fig. 14)

Fig. 14

Fixing screw

CRD3723A_N 02.10.17 0:04 PM Page 17

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer deh p5500mp Seite 56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer deh p5500mp

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info