425037
34
Zoom out
Zoom in
Vorherige Seite
1/112
Nächste Seite
34
<DRB1317>
En/Fr
TROUBLESHOOTING
Incorrect operations are often mistaken for trouble and malfunctions. If you think there is something wrong with this component, check
the points below. Sometimes the trouble may originate from another component. Thus, also check the other electrical appliances also in
use.
If the trouble cannot be rectified even after checking the following items, contact your dealer or nearest PIONEER service center.
Problem Possible Cause Countermeasure
The power does not turn
on.
There is little or no sound.
Sound is distorted.
Cant use cross fading.
CD players fader wont
start.
Effects dont work.
External effectors sound
distorted.
Cant measure BPM.
Measured BPM values are
strange.
Measured BPM value
differs from value indicated
on CD.
Cant use CH-4s PHONO 3
input terminal.
÷ The power cord has not been connected.
÷ The input selector switch is in the wrong
position.
÷ The connection cable hasn’t been connected
properly or has been disconnected.
÷ The terminal or plug is dirty.
÷ The master output level control (MASTER
LEVEL ATT.) on the back has been set too
low.
÷ Master output level is too high.
÷ Input level is too high.
÷ ASSIGN A & B haven’t been set correctly.
÷ Fader start switch is off.
÷ The player control terminal on the back hasn’t
been connected.
÷ Effect/sampler selector switch hasn’t been
set correctly.
÷ Effect/sampler parameter 2 knob was set to
the minimum (MIN.).
÷ The input level from the external effector is
too high.
÷ Input level is too high or too low.
÷ BPM can’t be measured in some cases,
depending on the music.
÷ Because of different BPM measurement
methods, somewhat different values may be
indicated.
÷ A sub-microphone has been connected.
÷ Connect the cord to a power outlet.
÷ Set the input selector switch to the device
currently playing.
÷ Connect it properly.
÷ Clean and reconnect.
÷ Adjust the master output level control
(MASTER LEVEL ATT.) on the back.
÷ Adjust the master output level control
(MASTER LEVEL ATT.) on the back.
÷ Adjust the TRIM knob so that the input level
approaches 0dB on the peak level meter.
÷ Set the ASSIGN switches to the correct cross
fader source.
÷ Turn on the fader start switch.
÷ Use the control cable to connect the unit and
CD player.
÷ Correctly select the channel to which effects
should be applied.
÷ Adjust the effect/sampler parameter 2 knob.
÷ Lower the external effector’s output level or
adjust the return level using the effect/
sampler parameter 2 knob.
÷ Adjust the TRIM knob so that the input level
approaches 0dB on the peak level meter.
÷ Adjust input levels of other channels to
approach 0dB.
÷ Press the TAP switch and set BPM manually.
÷ No countermeasures necessary.
÷ Disconnect the sub- microphone.
Static electricity or other external interference may cause the unit to malfunction. To restore normal operation, turn the power off and then
on again.
En
34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Pioneer djm 600 dj mixer 5 kanaals wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info