Bedienungsanleitung Pioneer GM-ME500X1 (Seite 3 von 7) (Englisch, Französisch)

811527

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

Connections when using

the speaker input wire

Connect the stereo speaker output wires to

the amplifier using the supplied speaker input

wire with RCA pin cord.

1Stereo

2Speaker output

3Red: Right +

4Black: Right *

5Black: Left *

6White: Left +

7Speaker input wire with RCA pin cord

To the RCA input jack of this unit

Notes

!If speaker input wires from a headunit are

connected to this amplifier, the amplifier will

automatically turn on when the headunit is

turned on. When the headunit is turned off,

the amplifier turns off automatically. This

function may not work with some headunits.

In such cases, please use a system remote

control wire (sold separately). If multiple am-

plifiers are to be connected together synchro-

nously, connect the head unit and all

amplifiers via the system remote control wire.

!This amplifier automatically selects an input

signal mode between the RCA level and the

speaker level by detecting an input signal.

Solderless terminal

connections

!Since the wire may become loose over

time, it must be periodically inspected and

tightened as necessary.

!Do not solder or bind the ends of the

twisted wires.

!Fasten while making sure to not to clamp

the insulating sheath of the wire.

!Use the supplied hexagonal wrench to

tighten and loosen the terminal screw of

the amplifier and use it to securely fasten

the wire. Be careful to avoid excessive tigh-

tening of this screw, which may damage

the wire.

Connecting the power terminal

WARNING

If the battery wire is not securely fixed to the term-

inal using the terminal screws, there is a risk of

overheating, malfunction and injury, including

minor burns.

!Always use the recommended battery and

ground wire, which is sold separately. Con-

nect the battery wire directly to the boat

battery positive (+) terminal and the

ground wire to the boat body.

!Recommended wires size (AWG: American

Wire Gauge) is as follows. The battery wire,

the ground wire and the optional direct

ground wire must be same size.

!Use a wire of 12 AWG to 16 AWG wire for

the speaker wire.

1 Route battery wire from engine com-

partment to the boat interior.

!When drilling a cable pass-thru into a bulk

head or barrier wall, route the cable

through carefully and seal the hole to pre-

vent fumes from seeping from engine com-

partment to other areas.

<5707000012820V>9

Connecting the units

After completing all other amplifier connec-

tions, finally connect the battery wire terminal

of the amplifier to the positive +battery term-

inal.

1Positive +terminal

2Battery wire (sold separately)

The maximum length of the wire between

the fuse and the positive +terminal of the

battery is 30 cm (12 in.).

3Fuse (80 A) (sold separately)

Each amplifier must be separately fused at

80 A.

2 Use wire cutters or a utility knife to

strip the end of the battery wire, ground

wire and system remote control wire to ex-

pose about 10 mm (3/8 in.) of the end of

each of the wires, and then twist the ex-

posed ends of the wires.

Twist

10 mm (3/8 in.)

3 Connect the wires to the terminal.

Fix the wires securely with the terminal

screws.

1Battery wire

2Power terminal

3Ground wire

4GND terminal

5System remote control wire

6System remote control terminal

7Terminal screws

<5707000012820V>10

Connecting the units

Connecting the speaker output

terminals

1 Use wire cutters or a utility knife to

strip the end of the speaker wires to ex-

pose about 10 mm (3/8 in.) of wire and

then twist the wire.

Twist

10 mm (3/8 in.)

2 Connect the speaker wires to the

speaker output terminals.

Fix the wires securely with the terminal

screws.

1Terminal screws

2Speaker wires

3Speaker output terminals

Before installing the amplifier

WARNING

!To ensure proper installation, use the supplied

parts in the manner specified. If any parts

other than those supplied are used, they may

damage internal parts of the amplifier, or be-

come loose causing the amplifier to shut

down.

!Do not install in:

—Places where injury could occur if the boat

stops suddenly.

—Places where it may interfere with the

boat's operator.

!Install tapping screws in such a way that the

screw tip does not touch any wire. This is im-

portant to prevent wires from being cut by vi-

bration of the boat, which can result in fire.

!Make sure that wires do not get caught in the

sliding mechanism or touch the legs of a per-

son in the boat as short-circuit may result.

!When drilling to install the amplifier, always

confirm no parts are behind the panel and

protect all cables and important equipment

(e.g. cables, wiring, hoses, and modules) from

damage.

CAUTION

!To ensure proper heat dissipation of the ampli-

fier, ensure the following during installation:

—Allow adequate space above the amplifier

for proper ventilation.

—Do not cover the amplifier.

!Place all cables away from hot places, such

as near the heater outlet.

!The optimal installation location differs de-

pending on the boat model. Secure the ampli-

fier at a sufficiently rigid location.

!Check all connections and systems before

final installation.

<5707000012820V>11

Connecting the units Installation

Example of installation on

the chassis

1 Place the amplifier in the desired instal-

lation location.

Insert the supplied tapping screws (4 mm ×

18 mm (5/32 in. × 3/4 in.)) into the screw holes

and push on the screws with a screwdriver so

they make an imprint where the installation

holes are to be located.

2 Drill 2.5 mm (3/32 in.) diameter holes in

the chassis.

3 Install the amplifier with the use of

supplied tapping screws (4 mm × 18 mm

(5/32 in. × 3/4 in.)).

1Tapping-screws (4 mm × 18 mm (5/32 in. ×

3/4 in.))

2Drill a 2.5 mm (3/32 in.) diameter hole

3Installation surface

4Hole-to-hole distance: 229.5 mm (9-1/32 in.)

5Hole-to-hole distance: 191.5 mm

(7-17/32 in.)

4 Attach the fuse cover and panel cover.

Attach the panel cover to the amplifier using

the supplied machine screws (3 mm × 10 mm

(1/8 in. × 3/8 in.)).

Machine screws (3 mm × 10 mm (1/8 in. × 3/

8 in.))

When installing the amplifier in a place that is

prone to getting wet, install it to a wall with

the power/speaker output terminals and RCA

jacks on the left and right sides.

<5707000012820V>12

Installation

Pioneer GM-ME500X1 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer GM-ME500X1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info