Bedienungsanleitung Pioneer HTP-330 (Seite 22 von 62) (Englisch)

573849

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

Surround sound settings

3 Use

/

(cursor up/down) to select a setting.

Select one of the following:

•

DRC OFF

(default)

– No dynamic range adjustment

(use when listening at higher volume)

•

DRC MID

– Mid setting

•

DRC HIGH

– Dynamic range is reduced (loud sounds

are reduced in volume while quieter sounds are

increased)

4 Press

ENTER

to exit.

Dual mono setting

Specifies how dual mono encoded Dolby Digital or DTS

soundtracks should be played. You can also use this

setting to switch the audio channel on DVD-RW discs

recorded with bilingual audio.

1 Press

SETUP

2 Use the

/

(cursor left/right) buttons to select

DUALMONO, then press

ENTER

3 Use

/

(cursor up/down) to select a setting.

Select one of the following:

•

CH1 MONO

(default)

– Only channel 1 is played

•

CH2 MONO

– Only channel 2 is played

•

CH1/CH2

– Both channels are played through the

front speakers

4 Press

ENTER

to exit.

Adjusting the channel levels using the

test tone

If you prefer, you can set the channel levels using a test

tone as a reference, rather than playing a source (see

Channel level setting

on page 21). A test tone is played

through each speaker in turn, allowing you to adjust the

level as it plays.

Note that the channel level settings for stereo sources

are independent of the settings for surround sound

sources.

1 Press

SURROUND

to select the Auto listening

mode.

• If you want to set the channel levels for stereo (two

channel) playback, select the

STEREO

listening

mode.

2 Press

TEST TONE

The test tone is output from each speaker in turn.

3While a test tone is playing, use the

/

(cursor

up/down) buttons to adjust that channel level.

The aim is to adjust the levels so that you hear the test

tone at the same volume from each speaker. You can

adjust the level of each channel by ±10 dB.

• You can adjust the overall volume of test tone output

using the

VOLUME

+/–

buttons (this does not affect

the channel level settings).

• If the system is in Stereo or Virtual mode, you will not

be able to adjust the center or surround channels.

• Because of the ultra low frequencies the subwoofer

produces, it may sound quieter than it really is. We

suggest adjusting the subwoofer level while listening

to a source. See the method described in

Channel

level setting

on page 21.

4When you’re done, press

ENTER

to exit test tone

setup.

• If you use the Auto MCACC feature again, it will

overwrite the settings you have made here.

TUNE

ENTER

CLEAR

SOUND

SETUP

TEST

TONE

CHANNEL

SOUND

RETRIEVER

MCACCADVANCED F.S.SURRSURROUND

SLEEP

VOLUME

TUNE

ENTER

TEST

TONE

SURROUND

HTP-330.book 22 ページ２００７年３月２７日　火曜日　午後６時８分

Downloaded from www.Manualslib.com manuals search engine

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer HTP-330 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info