Bedienungsanleitung Pioneer HTZ787DVD (Seite 18 von 126) (Englisch)

573876

Zoom out

Zoom in

Vorherige Seite

1/126

Nächste Seite

Getting started04

1 Connect the microphone to the MCACC

MIC jack on the front panel.

2 Place the microphone at your normal

listening position.

Place it about ear height, and make sure it is

level by using a table or chair.

Make sure there are no obstacles between the

speakers and the microphone.

3 If the system is off, press

 STANDBY/ON to turn the power on.

When the speaker layout menu appears, see

Setting Speaker Layout on page 17 and select a

proper setting.

4Press SHIFT+MCACC.

Try to be as quiet as possible after pressing

SHIFT+MCACC. The volume increases

automatically and the system outputs a series

of test tones.

• Press SHIFT+MCACC to cancel and revert

to the previous Auto MCACC settings.

• If the noise level is too high, NOISY blinks

in the display for five seconds. To exit and

check the noise levels

, press

SHIFT+MCACC, or to try again, press

ENTER when RETRY shows in the display.

• If you see an ERR MIC or ERR SP message

in the display, there may be a problem with

your mic or the speaker connections. To try

again, press ENTER when you see RETRY.

When MCACC setup is complete, the volume

level returns to normal and COMPLETE

shows

in the display, indicating that the MCACC

setup is complete and Acoustic Calibration EQ

has been activated.

• Be sure to disconnect the microphone

from this unit upon completion of the Auto

MCACC setup.

Using the on-screen displays

For ease of use, this system makes extensive

use of graphical on-screen displays (OSDs).

All the screens are navigated in basically the

same way, using , , ,  to change the

highlighted item and pressing ENTER to select

it.

Important

• Throughout this manual, ‘Select’ means

use the cursor buttons to highlight an item

on-screen, then press ENTER.

Note

1 • If the room environment is not optimal for the Auto MCACC setup (too much ambient noise, echo off the walls, obstacles

blocking the speakers from the microphone) the final settings may be incorrect. Check for household appliances (air conditioner,

fridge, fan, etc.), that may be affecting the environment and switch them off if necessary.

• Some older TVs may interfere with the operation of the mic. If this seems to be happening, switch off the TV during the Auto

MCACC setup.

USB

PHONES

MAIN SUB

MCACC SET UP

MIC

MAIN SUB

MCACC SET UP

MIC

2 If this doesn’t work, press SHIFT+MCACC, turn off the power, and check the problem indicated by the error message, then try

the Auto MCACC setup again.

3If COMPLETE doesn’t appear, it is likely an error occurred during the setup. Please check all connections and try again.

4See Listening with Acoustic Calibration EQ on page 24 to switch on/off Acoustic Calibration EQ.

5 The screen saver will appear after five minutes of inactivity.

Button What it does

HOME

Displays/exits the on-screen display

 Changes the highlighted menu item

ENTER

Selects the highlighted menu item

RETURN

Returns to the main menu without

saving changes

HTZ585DVD_EN.book 18 ページ２００９年３月１９日　木曜日　午後６時３５分

Downloaded from www.Manualslib.com manuals search engine

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer HTZ787DVD Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info