Bedienungsanleitung Pioneer MVH 8200 (Seite 31 von 48) (Englisch)

454588

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Initial Settings

1 Press SRC/OFF and hold until the unit

turns off.

2 Press M.C. to display the initial setting

menu.

3 Turn M.C. to select the initial setting.

After selecting, perform the following proce-

dures to set the initial setting.

FM step (FM tuning step)

Normally, the FM tuning step employed by seek tun-

ing is 50 kHz. When AF or TA is on, the tuning step

automatically changes to 100 kHz. It may be prefer-

able to set the tuning step to 50 kHz when AF is on.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the FM tuning step.

100kHz (100 kHz)—50kHz (50 kHz)

3 Press M.C. to confirm the selection.

Auto PI (auto PI seek)

The unit can automatically search for a different sta-

tion with the same programming, even during preset

recall.

1 Press M.C. to turn Auto PI seek on or off.

A-EQ Measurement (auto-equalizing)

The auto-equalizer is an equalizer curve created by

auto EQ (refer to Auto EQ (auto-equalizing) on the next

page).

You can turn the auto-equalizer on or off.

Rear Speaker (rear output and subwoofer setting)

This unit’s rea r output (rear speaker leads output and

RCA rear output) can be used for full-range speaker

(Full) or subwoofer (Subwoofer) connection. If you

switch the rear output setting to Subwoofer, you can

connect a rear speaker lead directly to a subwoofer

without using an auxiliary amp.

Initially, the unit is set for rear full-range speaker con-

nection (Full).

1 Press M.C. to display the setting mode.

2 Turn M.C. to change the setting.

Subwoofer (subwoofer)—Full (full-range speak-

er)

! Even if you change this setting, there is no

output unless you turn the subwoofer output

on (refer to Subwoofer1 (subwoofer on/off

setting) on page 28).

! If you change this setting, subwoofer output

in the audio menu will return to the factory

settings.

3 Press M.C. to confirm the selection.

Demonstration (demo display setting)

1 Press M.C. to turn the demo display on or off.

Video Signal (video signal setting)

Be sure to adjust the video signal setting to one that

is suitable for your country.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select an appropriate video signal.

NTSC—PAL

3 Press M.C. to confirm the selection.

BT Memory Clear (resetting the Bluetooth wireless

technology module)

This function is available only for MVH-8200BT.

Bluetooth telephone data can be deleted. To protect

personal information, we recommend deleting this

data before tran sferring the unit to other persons. The

following settings will be deleted.

! phone book entries on the Bluetooth telephone

! preset numbers on the Bluetooth telephone

! registration assignment of the Bluetooth tele-

phone

! call history of the Bluetooth telephone

! information of the connected Bluetooth telephone

! PIN code

1 Press M.C. to display the setting mode.

2 Use M.C. to select Yes.

Turn to change the mode. Press to select.

Cleared is displayed and the settings are deleted.

To cancel, select No.

! While this function is in use, do not turn off

the engine.

Section

Operating this unit

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer MVH 8200 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer MVH 8200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info