Bedienungsanleitung Pioneer MVH-AV280BT (Seite 6 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

649405

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

1 Dashboard

4 Attach the trim ring.

1 Trim ring

2 Groove

Attach the trim ring with the side with a groove facing

downward.

Installation using the screw

holes on the side of this

product

1 Fastening this product to the factory

radio-mounting bracket.

Position this product so that its screw holes are aligned with

the screw holes of the bracket, and tighten the screws at three

locations on each side.

Use either the truss head screws (5 mm × 9 mm) or flush

surface screws (5 mm × 9 mm), depending on the shape of the

bracket’s screw holes.

Precautions before installation

CAUTION

Never install this product in places where, or in a manner

that:



Could injure the driver or passengers if the vehicle

stops suddenly.



May interfere with the driver’s operation of the

vehicle, such as on the floor in front of the driver’s

seat, or close to the steering wheel or gearstick.



To ensure proper installation, be sure to use the

supplied parts in the manner specified. If any parts

are not supplied with this product, use compatible

parts in the manner specified after you have the parts’

compatibility checked by your dealer. If parts other

than supplied or compatible ones are used, they may

damage internal parts of this product or they may

work loose and the product may become detached.



Do not install this product where it may (i) obstruct

the driver’s vision, (ii) impair the performance of any

of the vehicle’s operating systems or safety features,

including airbags, hazard lamp buttons or (iii) impair

the driver’s ability to safely operate the vehicle.



Never install this product in front of or next to the

place in the dashboard, door, or pillar from which one

of your vehicle’s airbags would deploy. Please refer

to your vehicle’s owner’s manual for reference to the

deployment area of the frontal airbags.

Before installing

 Consult with your nearest dealer if installation requires

drilling holes or other modifications of the vehicle.



Before making a final installation of this product, temporarily

connect the wiring to confirm that the connections are

correct and the system works properly.



Do not install this product in a position where the opening

of the LCD panel is obstructed by any obstacles, such as the

gearstick. Before installing this product, be sure to leave

sufficient space so that the LCD panel does not obstruct the

gearstick when it is fully opened. This may cause interfer-

ence with the gearstick, or a malfunction of the mechanism

of this product.

Installation notes

 Do not install this product in places subject to high tempera-

tures or humidity, such as:



Places close to a heater, vent or air conditioner.

 Places exposed to direct sunlight, such as on top of the

dashboard.



Places that may be exposed to rain, such as close to the door

or on the vehicle’s floor.



Install this product horizontally on a surface within 0 to

30 degrees tolerance (within 5 degrees to the left or right).

Improper installation of the unit with the surface tilted more

than these tolerances increases the potential for errors in

the vehicle’s location display, and might otherwise cause

reduced display performance.

30°

 When installing, to ensure proper heat dispersal when using

this unit, make sure you leave ample space behind the rear

panel and wrap any loose cables so they are not blocking the

vents.

Leave ample

space

5 cm

Before installing this product

1 Remove the trim ring.

Extend top and bottom of the trim ring outwards to remove the

trim ring.

1 Trim ring

2 Insert the supplied extraction keys into both

sides of the unit until they click into place.

3 Pull the unit out of the holder.

1 Extraction key

Installation with the holder

1 Install the holder into the dashboard.

2 Secure the mounting sleeve by using a screw-

driver to bend the metal tabs (90°) into place.

1 Dashboard

2 Holder

3 Install this product into the holder.

Installation

6 < QRD3362-A >< QRD3362-A >

Installation Installation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer MVH-AV280BT Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer MVH-AV280BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info