Bedienungsanleitung Pioneer ND-BC20PA (Seite 6 von 8) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

811500

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Fig. 16

Abb. 16

Fig. 17

Abb. 17

Fig. 18

Abb. 18

Fig. 19

Abb. 19

① Pull out from here ② Hinge

③ Harness cover

⑤ Hatch

④ Rear view

camera

① Rear view camera

② Hatch

③ Cord

② Waterproof pad

Fig. 20

Abb. 20

① Plastic clamp

③ Rubber packing

④ Make a U-shaped loop in

the lead outside the rubber

packing to prevent rain-

water from flowing along

the lead into the interior

of the vehicle.

Connection <ENGLISH>

Note:

• This unit is for vehicles with a 12-volt battery and

negative grounding. Before installing it in a recreational

vehicle, truck, or bus, check the battery voltage.

• To avoid shorts in the electrical system, be sure to

disconnect the battery cable before beginning

installation.

• Refer to the owner’s manual for details on connecting the

other units, then make connections correctly.

• Secure the wiring with cable clamps or adhesive tape. To

protect the wiring, wrap adhesive tape around them where

they lie against metal parts.

• Route and secure all wiring so it cannot touch any

moving parts, such as the gear shift, handbrake and seat

rails. Do not route wiring in places that get hot, such

as near the heater outlet. If the insulation of the wiring

melts or gets torn, there is a danger of the wiring short-

circuiting to the vehicle body.

• Do not shorten any leads.

• Never feed power to other equipment by cutting the

insulation of the power supply lead of the unit and

tapping into the lead. The current capacity of the lead will

be exceeded, causing over heating.

• When replacing the fuse, be sure to only use a fuse of the

rating prescribed on the fuse holder.

• To minimize noise locate the TV antenna cable, radio

antenna cable and RCA power supply cable as far away

from each other as possible.

• Connection to a TV with an RCA video input is possible,

but confirm whether the TV you use has a reverse gear

connection function.

• If this unit is installed in a vehicle that does not have an

ACC (accessory) position on the ignition switch, the red

lead of the unit should be connected to a terminal coupled

with ignition switch ON/OFF operations. If this is not

done, the vehicle battery may be drained when you are

away from the vehicle for several hours.

ACC position No ACC position

• Cords for this product and those for other products may

be different colors even if they have the same function.

When connecting this product to another product, refer to

the supplied manuals of both products and connect cords

that have the same function.

Connection sample (Fig. 16)

① Image processing unit power supply

② Rear view camera connector

③ RCA power supply cable connector

④ Rear view camera

⑨ Button unit

⑩ Button unit connector

Video input jack

Connect to video input jack.

⑤ RCA pin

Accessory power supply

To electric terminal controlled by ignition

switch (12 V DC) ON/OFF.

⑥ Red

⑦ Fuse (1A)

Ground

To vehicle (metal) body.

⑧ Black

Cord installation (Fig. 17)

① Plastic clamps

② Rear view camera

③ RCA power supply cable

④ Product with a video input jack

(Hideaway unit etc.)

⑤ Image processing unit power supply

⑥ Button unit

⑦ Made with a rasp etc.

⑧ Scuff plate

⑨ Plastic clamp

⑩ Waterproof plate

⑪ Double-sided tape (rectangular)

Cord installation points (Fig. 18)

• When pulling the cord out of the car,

pull from the outer side of the hatch

harness cover and hinge.

① Pull out from here

② Hinge

③ Harness cover

④ Rear view camera

⑤ Hatch

After cord installation (Fig. 19, Fig. 20)

• Open and close the hatch door slowly

to confirm that the cord is not rubbing

against the rim of the door.

① Rear view camera

② Hatch

③ Cord

• When the rear view camera cord cannot

be pulled out from the lower side due to

the type of car.

As shown in the figure 18, bend the cord

into a U shape in front of the waterproof

pad, making sure that rain water cannot

enter the car by running down the cord.

① Plastic clamp

② Waterproof pad

③ Rubber packing

④ Make a U-shaped loop in the lead outside

the rubber packing to prevent rainwater from

flowing along the lead into the interior of the

vehicle.

① Image processing unit power supply

③ RCA power supply

cable connector

② Rear view camera

connector

⑩ Button unit

connector ⑨ Button unit

⑥ Red

⑤ RCA pin

⑧ Black

⑦ Fuse (1A) 3 m (9 ft. 10 in.)

3 m (9 ft. 10 in.)

④ Rear view camera

1.5 m (4 ft. 11 in.)

7 m (23 ft.)

① Plastic clamps

② Rear view

camera

④ Product with a video input

jack (Hideaway unit etc.)

⑦ Made with a rasp etc.

⑧ Scuff plate

⑨ Plastic clamp ⑩ Waterproof plate

③ RCA power

supply cable

⑤ Image processing unit power supply

⑥ Button unit

4 m (13 ft. 2 in.)

⑪ Double-sided

tape (rectangular)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer ND-BC20PA Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer ND-BC20PA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info