Bedienungsanleitung Pioneer RCS-606H-S (Seite 134 von 152) (Englisch)

573927

134

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

The Initial Setup menu

134

Additional information about the TV system

settings

About the input line system

This recorder is compatible with PAL, SECAM, 3.58 NTSC

and PAL-60 TV systems. The Input Line System and Input

Colour System settings determine how the recorder

treats incoming video signals from an external input or

the built-in TV tuner.

Please note the following points when changing the

input line system:

• When the current input is a built-in tuner channel

preset, changing the input line system will usually

also affect the input line system of the AV2 (INPUT 1/

DECODER) input. However if the AV2/L1 In setting is

set to Decoder, then the L2 input is affected instead.

• If, when the Input Line System setting is changed, the

screen goes blank (due to incompatibility with your

TV), you can switch back by pressing and holding the

front panel  STOP button then pressing  OPEN/

CLOSE (also front panel) while the recorder is

stopped.

• When you switch the Input Line System setting the

Copy List is erased. If you switch the setting using the

 STOP button and  OPEN/CLOSE buttons as

described above, there is no confirmation, so please

use with care.

• You can’t mix recordings of different TV line systems

on the same disc.

• When you change this setting, the Input Colour

System setting also changes (see below).

About NTSC on PAL TV

Depending on the Input Line System setting and the

NTSC on PAL TV setting, the signal format output when

the recorder is stopped varies as shown in the table

below.

Front Panel Display On • The time is shown in the front panel display when the recorder is in standby.

Off The front panel display is switched off in standby (although it still lights dimly

when setting a timer recording).

Remote Control

Mode

Recorder 1–3

(default: Recorder 1)

If you are using more than one recorder in the same room, set them to different

IDs. This setting sets the recorder ID; to change the remote controller ID, press

and hold RETURN then press 1, 2 or 3 to set. The remote will only control a

recorder with the same ID.

AV. Link This Recorder

Only •

Signals received through the AV input when the recorder is in standby are not

passed through to the AV output.

Pass Through Signals received when in standby are passed though to the output for connected

devices. (Note that during EPG data download, the EPG data is not passed

through.)

When set to Pass Through, make sure to set Power Save (page 128) to Off.

DivX VOD Registration Code Use to display the recorder’s DivX registration code. See DivX video compatibility

on page 47 and DivX® VOD content on page 47.

Set Preview

(HDD only)

Quick Preview • When in the Disc Navigator, the thumbnail video plays short excerpts from

throughout the selected title. (Note that edited titles that will play normally from

the beginning.)

Normal The thumbnail video plays from the beginning of the title.

Setting Options Explanation

Input Line

System

NTSC on PAL

Output when

stopped

625 System Off PAL

On PAL

525 System Off NTSC

On PAL–60

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer RCS-606H-S Seite 134

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer RCS-606H-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info