Bedienungsanleitung Pioneer s 31 c (Seite 3 von 59) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

419756

Zoom out

Zoom in

Vorherige Seite

1/59

Nächste Seite

English

How to install

Choosing where to place the speaker systems

• Sounds played through speaker systems are easily affected in

subtle ways by the conditions in the listening space.

• For best sound, choose a solid floor upon which to place the

speakers, and position the speakers as shown below. The level

of low sounds can be adjusted by moving the speakers closer

to or further from the wall. Adjust the speakers so that they are

equidistant from their respective side walls to assure balanced

sound.

• If the room has a lot of reverberation, we recommend hanging

heavy fabric on the walls, and/or putting a carpet on the floor

to damp the sound. For best results, cover walls completely.

• This speaker is a bookshelf-type speaker which will give best

performance when placed on a solid, level surface off the floor.

Placing the speaker directly on the floor will result in boomy,

undefined sound.

• Pioneer assumes no liability whatsoever for damages

resulting from assembly, improper mounting, insufficient

reinforcement, misuse of the product, acts of nature, etc.

Using the Foam Plug

On the rear side of the unit, a foam plug is provided to allow

adjustment of the bass sound. The foam plug can be removed if

desired to produce a different bass emphasis.

The following can be taken as general guidelines for use of the

foam plug:

• Mounted in the middle of a rack: Leave the foam plug in place

• Mounted on the top of a rack or on the floor: Remove the foam

plug

When using the silicon rubber feet

These speaker systems have been provided with silicon rubber

feet. Use them to adjust the four corners to produce optimum

stability.

Using the template (see end page) will allow easiest adjustment of

the setting angle.

Using the template

1 Open the hole in the template along the line indicating

your desired setting angle.

2 Align the line with the front of the unit, and then align

the template with the cabinet.

3 Affix the four silicon rubber feet in alignment with the

four cut-out holes.

Attaching and Removing the Grille

It is recommended that this speaker system be used with the grille

net attached, but it can be removed if desired. To remove, follow

these instructions:

1 To remove the grille, place your fingers at the outside of

the grille toward the bottom and pull gently outward. Then

do the same at the top to detach.

2 To reattach the grille, hold the speaker grille with the

triangular symbol pointing upward, then align the four pins

on the back side of the grille with the holes in the speaker

and press in firmly.

Do not force the foam plug into the hole excessively,

since it might be pressed inside the speaker and be

impossible to remove.

50 cm

(19

/16 in.)

20 cm

/8 in.)

foam plug

S-31C_En.fm 3 ページ２００９年７月２９日　水曜日　午後４時１６分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer s 31 c Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info