Bedienungsanleitung Pioneer S-DV1SW (Seite 10 von 94) (Englisch)

574059

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

Getting started02

1 Connect the microphone to the MCACC

MIC jack on the rear panel.

2 Place the microphone at your normal

listening position.

Place it about ear height, and make sure it is

level by using a table or chair.

Make sure there are no obstacles between the

speakers and the microphone.

3 If the system is off, press



STANDBY/ON to turn the power on.

If the tuner is selected, switch the input source.

4 Press SHIFT+MCACC.

Try to be as quiet as possible after pressing

SHIFT+MCACC

. The volume increases

automatically and the system outputs a series

of test tones.

• Press

SHIFT+MCACC

to cancel and revert

to the previous Auto MCACC settings.

• If the noise level is too high,

NOISY

blinks

in the display for five seconds. To exit and

check the noise levels

, press

SHIFT+MCACC

, or to try again, press

ENTER

when

RETRY

shows in the display.

• If you see an

ERR MIC

ERR SP

message

in the display, there may be a problem with

your mic or the speaker connections. To try

again, press

ENTER

when you see

RETRY

When the MCACC setup is complete, the

volume level returns to normal and

COMPLETE

shows in the display, indicating

that the MCACC setup is complete and

Acoustic Calibration EQ has been activated.

Using the on-screen displays

For ease of use, this system makes extensive

use of graphical on-screen displays (OSDs).

All the screens are navigated in basically the

same way, using









to change the

highlighted item and pressing

ENTER

to select

it.

Important

• Throughout this manual, ‘Select’ means

use the cursor buttons to highlight an item

on-screen, then press

ENTER

Tip

• The button guide at the bottom of every

OSD screen shows you which buttons

you’ll need to use for that screen.

Note

1• If the room environment is not optimal for the Auto MCACC setup (too much ambient noise, echo off the walls, obstacles

blocking the speakers from the microphone) the final settings may be incorrect. Check for household appliances (air condition-

er, fridge, fan, etc.), that may be affecting the environment and switch them off if necessary.

• Some older TVs may interfere with the operation of the mic. If this seems to be happening, switch off the TV during the Auto

MCACC setup.

2 If this doesn’t work, press

SHIFT+MCACC

, turn off the power, and check the problem indicated by the

ERR

message, then try

the Auto MCACC setup again.

AM LOOP

UNBAL

Ω

S-VIDEO

VIDEO

COMPONENT

VIDEO

ANTENNA

VIDEO OUT

CONTROL

MCACC

MIC

3 If

COMPLETE

doesn’t appear, it is likely an error occurred during the setup. Please check all connections and try again.

4 See

Listening with Acoustic Calibration EQ

on page 15 to switch on/off Acoustic Calibration EQ.

5 The screen saver will appear after five minutes of inactivity.

Button

What it does

HOME

Displays/exits the on-screen display



Changes the highlighted menu item

ENTER

Selects the highlighted menu item

RETURN

Returns to the main menu without

saving changes

XV-DV353_555.book 10 ページ２００６年４月７日　金曜日　午後６時１８分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer S-DV1SW Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info