Bedienungsanleitung Pioneer SC-1223 (Seite 37 von 119) (Englisch)

536834

Zoom out

Zoom in

Vorherige Seite

1/119

Nächste Seite

Basic Setup

Automatically conducting optimum sound tuning (Full Auto

MCACC)

The Full Auto MCACC Setup measures the acoustic characteristics of your listening area, taking into account

ambient noise, speaker connection and speaker size, and tests for both channel delay and channel level. After

you have set up the microphone provided with your system, the receiver uses the information from a series of test

tones to optimize the speaker settings and equalization for your particular room.

Important

! Make sure the microphone and speakers are not moved during the Full Auto MCACC Setup.

! Using the Full Auto MCACC Setup will overwrite any existing settings for the MCACC preset you select.

! Before using the Full Auto MCACC Setup, the headphones should be disconnected.

! The OSD display is only displayed when the receiver’s HDMI OUT 1 terminal and the TV’s HDMI input are

connected with an HDMI cable. If the TV is connected with anything other than an HDMI cable, watch the front

panel display while performing the various operations and making settings.

CAUTION

! The test tones used in the Full Auto MCACC Setup are output at high volume.

THX

1 Press u STANDBY/ON to switch on the receiver and your TV.

Make sure that the TV’s video input is set to this receiver.

2 Connect the microphone to the MCACC SETUP MIC jack on the front panel.

PHONES

SPEAKERS

MULTI-ZONE

CONTROL

ZONE 2

ON/OFF

HDZONE

ON/OFF

PHASE

CONTROL

MCACC

SETUP MIC

HDMI 5 INPUT/

MHL (

5V 0.9

)

AUTO/ALC/

DIRECTECO BAND TUNER EDIT

iPod iPhone iPad

DIRECT CONTROL

with USB

5V 2.1

Microphone

Tripod

Make sure there are no obstacles between the speakers and the microphone.

If you have a tripod, use it to place the microphone so that it’s about ear level at your normal listening position. If

you do not have a tripod, use some other object to install the microphone.

Install the microphone on a stable floor. Placing the microphone on any of the following surfaces may make

accurate measurement impossible:

! Sofas or other soft surfaces.

! High places such as tabletops and sofa tops.

The Full Auto MCACC display appears once the microphone is connected.

Speaker System : Normal

(

SB/FH

)

1a.Full Auto MCACC

A/V RECEIVER

Exit Return

START

EQ Type : SYMMETRY

MCACC : M1.MEMORY 1

THX Speaker : NO

! If you leave the GUI screen for over five minutes, the screen saver will appear.

3 Select the parameters you want to set.

! When data measurement is taken, the reverb characteristics data (both before- and after-calibration) that this

receiver had been storing will be overwritten.

! When measurement is taken of the reverb characteristics data other than SYMMETRY, the data are not

measured after the correction. If you will need to measure after correcting data, take the measurement using

the EQ Professional menu in the Manual MCACC setup (page 80).

If the speakers are connected using any setup other than Normal(SB/FH), be sure to set Speaker System before

the Full Auto MCACC Setup. See Speaker system setting on page 86.

! Speaker System – Shows the current settings. When this is selected and ENTER is pressed, the speaker

system selection screen appears. Select the proper speaker system, then press RETURN to return.

If you are planning on bi-amping your front speakers, or setting up a separate speaker system in another

room, read through Speaker system setting on page 86 and make sure to connect your speakers as necessary

before continuing to step 4.

! EQ Type – This determines how the frequency balance is adjusted. Normally select SYMMETRY. For details,

see Automatic MCACC (Expert) on page 79.

! MCACC – The six MCACC presets are used for storing surround sound settings for different listening posi-

tions. Simply choose an unused preset for now (you can rename it later in Data Management on page 83).

! THX Speaker – Select YES when using THX speakers (all speakers other than the front speakers are set to

SMALL). In other cases, leave at NO.

4 Press then select START.

5 Follow the instructions on-screen.

Make sure the microphone is connected, and if you’re using a subwoofer, make sure it is switched on and set to a

comfortable volume level.

6 Wait for the test tones to finish, then confirm the speaker configuration in the GUI screen.

A progress report is displayed on-screen while the receiver outputs test tones to determine the speakers present

in your setup. Try to be as quiet as possible while it’s doing this.

If no operations are performed for 10 seconds while the speaker configuration check screen is being displayed,

the Full Auto MCACC Setup will resume automatically. In this case, you don’t need to select ‘OK’ and press

ENTER in step 7.

! With error messages (such as Too much ambient noise! or Check microphone.), select RETRY after check-

ing for ambient noise (see Problems when using the Auto MCACC Setup on page 38) and verifying the mic

connection. If there doesn’t seem to be a problem, you can simply select GO NEXT and continue.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer SC-1223 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SC-1223

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info