Bedienungsanleitung Pioneer SC-1224 (Seite 71 von 126) (Englisch)

611801

Zoom out

Zoom in

Vorherige Seite

1/126

Nächste Seite

Using other functions

Setting What it does Option(s)

DETAIL

<d, e>

Adjusts how sharp edges appear.

(The image is only an example for checking the effect.)

c 0 to +8 d

Default: 0

BRIGHT

(Brightness)

<d, e>

Adjusts the overall brightness.

(The image is only an example for checking the effect.)

c –6 to +6 d

Default: 0

CONTRAST

<d, e>

Adjusts the contrast between light and dark.

(The image is only an example for checking the effect.)

c –6 to +6 d

Default: 0

HUE

<d, e>

Adjusts the red/green balance.

(The image is only an example for checking the effect.)

c –6 to +6 d

Default: 0

Setting What it does Option(s)

CHROMA

(Chroma Level)

<d, e>

Adjusts saturation from dull to bright.

(The image is only an example for checking the effect.)

c –6 to +6 d

Default: 0

BLK SETUP

(Black Setup)

<f>

Sets the black level according to the video input signal.

Normally select 0. If the black level is too bright due to the combina-

tion with the connected monitor, select 7.5.

7.5

ASP

(Aspect)

<g>

Specifies the aspect ratio when input signals are output at the HDMI

output. Make your desired settings while checking each setting on

your display (if the image doesn’t match your monitor type, cropping

or black bands appear).

THROUGH

NORMAL

a ! The default value changes depending on the type of input (page 75 ).

! If the video picture deteriorates when this settings is switched ON, switch it OFF.

! When connected to a video device using the component video input, set this setting to ON and watch with the HDMI output.

b ! When set to a resolution with which the TV (monitor) is not compatible, no picture is output. Also, in some cases no picture

will be output due to copyright protection signals. In this case, change the setting.

! When AUTO is selected, the resolution is selected automatically according to the capacity of the TV (monitor) connected by

HDMI. When PURE is selected, the signals are output with the same resolution as when input (see About the video converter on

page 24 ).

! When 1080/24p or 4K/24p is selected, the movement may be unnatural or the picture unclear, depending on the video signal

being input. In this case, set the resolution to something other than 1080/24p or 4K/24p.

! When PURE is selected and the input signal is 480i, the on-screen display cannot be displayed.

c ! P.MOTION is disabled when PCINEMA is set to ON.

! This setting have the effect only for pictures recorded in the interlaced scan format (480i/576i or 1080i signals).

d Adjustment is not possible unless V.ADJ (Advanced Video Adjust) is set to MEMORY.

e ! This setting is only displayed when the video signals below are being input:

— 480i, 576i, 480p, 576p, 720p, 1080i analog video signals

— 480i, 576i, 480p, 576p, 720p, 1080i, 1080p, 1080p24 HDMI video signals

f This adjustment is only possible when 480i signals are being input from the composite video jacks.

g ! If the image doesn’t match your monitor type, adjust the aspect ratio on the source component or on the monitor.

! This setting is only displayed when 480i/p or 576i/p video signals are being input.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer SC-1224 Seite 71

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SC-1224

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info