Bedienungsanleitung Pioneer SC-1224 (Seite 74 von 126) (Englisch)

611801

Zoom out

Zoom in

Vorherige Seite

1/126

Nächste Seite

Using other functions

Making an audio or a video recording

You can make an audio or a video recording from the built-in tuner, or from an audio or video source connected to

the receiver (such as a CD player or TV).

Keep in mind you can’t make a digital recording from an analog source or vice-versa, so make sure the compo-

nents you are recording to/from are hooked up in the same way (see Connecting your equipment on page 18

for more on connections).

! The receiver’s volume, Audio parameters (the tone controls, for example), and surround effects have no effect

on the recorded signal.

! Some digital sources are copy-protected, and can only be recorded in analog.

! Some video sources are copy-protected. These cannot be recorded.

Since the video converter is not available when making recordings (from the video OUT jacks) make sure to use

the same type of video cable for connecting your recorder as you used to connect your video source (the one you

want to record) to this receiver. For example, you must connect your recorder using Component video if your

source has also been connected using Component video.

1 Select the source you want to record.

You can use the input function buttons on the remote control or the front panel INPUT SELECTOR dial.

2 Prepare the source you want to record.

Tune to the radio station, load the CD, video, DVD etc.

3 Select the input signal according to the signal to be recorded.

Use the remote control’s AUDIO P. button.

4 Prepare the recorder.

Insert a blank tape, MD, video etc. into the recording device and set the recording levels. Refer to the instructions

that came with the recorder if you are unsure how to do this. Most video recorders set the audio recording level

automatically-check the component’s instruction manual if you’re unsure.

5 Start recording, then start playback of the source component.

Network settings from a web browser

Network settings can be made using the browser on a computer connected to the same LAN as the receiver.

1 Press u STANDBY/ON to switch on the receiver.

2 Turn on the computer’s power and launch the Internet browser.

3 Input the receiver’s IP address into the browser’s address input field.

Access the IP address“http://(the receiver’s IP address)” from a web browser. You can display the IP address of

the unit on the unit’s display by pressing the STATUS button on the remote control.

When connected with the receiver, the AVNavigator menu screen appears in the browser.

4 On the AVNavigator menu screen, select Network Setup.

5 Select the item you want to set.

Using the sleep timer

The sleep timer switches the receiver into standby after a specified amount of time so you can fall asleep without

worrying about the receiver being left on all night. Use the remote control to set the sleep timer.

% Press SLEEP repeatedly to set the sleep time.

30 min 60 min

Off 90 min

! You can check the remaining sleep time at any time by pressing SLEEP once. Pressing repeatedly will cycle

through the sleep options again.

! The sleep timer is valid for all zones. If any zone is on, the sleep timer continues functioning.

Dimming the display

You can choose between four brightness levels for the front panel display. Note that when selecting sources, the

display automatically brightens for a few seconds.

Turning off the display is effective for suppressing noise from the display that affects sound quality.

% Press DIMMER repeatedly to change the brightness of the front panel display.

! You can also choose to turn the display off. In this case, the FL OFF indicator lights.

Checking your system settings

Use the status display screen to check your current settings for features such as surround back channel process-

ing and your current MCACC preset.

1 Press STATUS.

2 Use i/j to check the system setting.

The information on the main unit display switches as shown below each time one of the buttons is pressed.

IP address f Audio format f Sampling frequency f MCACC memory f Auto phase control plus correc-

tion value f Input source to be played in ZONE 2 f Input source to be played in ZONE 3 (SC-2024 only) f

Input source to be played in HDZONE f HDMI output setting f Subzone to which HDZONE is output

! For some settings, some items are not displayed.

3 When you’re finished, press STATUS again to switch off the display.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer SC-1224 Seite 74

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SC-1224

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info