Bedienungsanleitung Pioneer SC-1224 (Seite 100 von 126) (Englisch)

611801

100

Zoom out

Zoom in

Vorherige Seite

1/126

Nächste Seite

100

FAQ

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong

with this component, check the points below. Sometimes the trouble may lie in another component. Investigate

the other components and electrical appliances being used. If the trouble cannot be rectified even after exercis-

ing the checks listed below, ask your nearest Pioneer authorized independent service company to carry out repair

work.

! If the unit does not operate normally due to external effects such as static electricity disconnect the power plug

from the outlet and insert again to return to normal operating conditions.

If the problem is not solved after the troubleshooting below, if the screen freezes unexpectedly or if the buttons on

the remote control or front panel stop working completely, do the following:

! Press u STANDBY/ON on the front panel to turn off the power, then turn the power back on.

If this does not solve the problem, turn off the power again, then press and hold the u STANDBY/ON button

on the front panel for at least five seconds. (The power turns on, then turns off after five seconds.)

! If the power cannot be turned off, press and hold u STANDBY/ON on the front panel for over five seconds. The

power will turn off. In this case, the various settings made on the receiver may be cleared. (However, settings

made when the power was turned off normally are not cleared.)

Power

Symptom Remedy

The power does not turn on. Make sure that the power cord is plugged in to an active power outlet.

Try disconnecting from the power outlet, then plugging back in.

Power cannot be turned off.

(ZONE 2 ON is displayed.)

Press the ZONE 2 button on the remote control for 1.5 seconds and then press the

u STANDBY/ON button to turn OFF the power.

Power cannot be turned off.

(ZONE 3 ON is displayed.)

Press the ZONE 3 button on the remote control for 1.5 seconds and then press the

u STANDBY/ON button to turn OFF the power.

Power cannot be turned off.

(HDZONE ON is displayed.)

Press the HDZONE button on the remote control for 1.5 seconds and then press the

u STANDBY/ON button to turn OFF the power.

The receiver suddenly switches off or

the iPod iPhone indicator blinks.

Check that there are no loose strands of speaker wire touching the rear panel or another

set of wires. If so, re-attach the speaker wires, making sure there are no stray strands.

The receiver may have a serious problem. Disconnect from the power and call a Pioneer

authorized independent service company.

During loud playback the power sud-

denly switches off.

Turn down the volume.

Lower the 63 Hz and 125 Hz equalizer levels in the Manual MCACC setup on page 85 .

Switch on the digital safety feature. While holding down ENTER on the front panel,

press u STANDBY/ON to set this receiver to the standby mode. Use TUNE i/j to

select D.SAFETY cOFFd, and then use PRESET k/l to select 1 or 2 (select D.SAFETY

cOFFd to deactivate this feature). If the power switches off even with 2 switched on, turn

down the volume. With 1 or 2 on, some features may be unavailable.

If there is very little low frequency information in the source material, change your

speaker settings to Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS

(see Speaker Setting on page 90 ).

The unit does not respond when the

buttons are pressed.

Try switching the receiver off, then back on again.

Try disconnecting the power cord, then connect again.

AMP ERR blinks in the display, then

the power automatically switches off.

The ADVANCED MCACC blinks and

the power does not turn on.

The receiver may have a serious problem. Do not try switching the receiver on. Unplug

the receiver from the wall and call a Pioneer authorized independent service company.

Symptom Remedy

The receiver suddenly switches off or

the FL OFF indicator blinks.

There is a possibility that the power supply circuit of the receiver has failed. Wait at least

one minute and then turn ON the power again. If the same symptom appears again after

turning ON the power again, stop using the receiver, disconnect the power cable and

request repair.

AMP OVERHEAT blinks in the dis-

play and the FL OFF indicator flash

and the power turns off.

Allow the unit to cool down in a well-ventilated place before switching back on (see

Installing the receiver on page 9 ).

Check whether the cables used to connect the speakers are short-circuited.

Wait at least 1 minute, then try turning the power on again.

The temperature within the unit has exceeded the allowablevalue.

Lower the volume level.

HDZONE cannot be turned on.

Set Output Setting at MAIN/HDZONE to HDZONE (page 95 ).

The receiver suddenly power off or

ADVANCED MCACC flashes.

The power unit is damaged. Unplug the receiver from the wall and call a Pioneer autho-

rized independent service company.

FAN STOP is displayed, then

iPod iPhone indicator blinks.

The built-in cooling fan is malfunctioning. Do not try switching the receiver on. Unplug

the receiver from the wall and call a Pioneer authorized independent service company.

Display blinks 12V TRG ERR. An error has arisen in the 12 V trigger jacks. Reconnect accurately then turn the power

back on.

No sound

Symptom Remedy

There is no sound output, the sound

gets cut off, or there is noise present.

If Fixed PCM in audio parameter is set to ON, you will not be able to playback audio in

formats other than PCM audio. For other audio formats than PCM audio, select OFF (See

Setting the Audio options on page 68 ).

No sound is output when an input

function is selected.

No sound is output from the front

speakers.

Check the volume, mute setting (press MUTE) and speaker setting (press OUT P.).

Make sure the correct input function is selected.

Check that the MCACC setup microphone is disconnected.

Make sure the correct input signal is selected (see Choosing the input signal on page

56 ).

Check that the source component is connected properly (see Connecting your equipment

on page 18 ).

Check that the speakers are connected properly (see Connecting the speakers on page

21 ).

No sound from the surround or

center speakers.

Check that the Stereo listening mode or the Front Stage Surround Advance mode isn’t

selected; select one of the surround listening modes (see Enjoying various types of play-

back using the listening modes on page 54 ).

Check that the surround/center speakers are not set to NO (see Speaker Setting on page

90 ).

Check the channel level settings (see Channel Level on page 91 ).

Check the speaker connections (see Connecting the speakers on page 21 ).

Pioneer SC-1224 Seite 100

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SC-1224

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info