Bedienungsanleitung Pioneer SC-LX56 (Seite 56 von 124) (Englisch)

491879

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

Listening to your system

Better sound using Phase Control

This receiver’s Phase Control feature uses phase correction measures to make sure your sound source arrives at

the listening position in phase, preventing unwanted distortion and/or coloring of the sound.

Phase Control technology provides coherent sound reproduction through the use of phase matching for an opti-

mal sound image. The default setting is on and we recommend leaving Phase Control switched on for all sound

sources.

% Press PHASE (PHASE CONTROL) to switch on phase correction.

The PHASE CONTROL indicator on the front panel lights.

Note

! Phase matching is a very important factor in achieving proper sound reproduction. If two waveforms are ‘in

phase’, they crest and trough together, resulting in increased amplitude, clarity and presence of the sound

signal. If a crest of a wave meets a trough, then the sound will be ‘out of phase’ and an unreliable sound image

will be produced.

! For discs created with standards other than Phase Control, the LFE channel is delayed upon recording in the

first place. Phase Control Plus function corrects for phase shifting on such discs. For instructions on setting

the Phase Control Plus, see Setting the Audio options on page 67.

! If your subwoofer has a phase control switch, set it to the plus (+) sign (or 0º). However, the effect you can

actually feel when PHASE CONTROL is set to ON on this receiver depends on the type of your subwoofer. Set

your subwoofer to maximize the effect. It is also recommended you try changing the orientation or the place of

your subwoofer.

! Set the built-in lowpass filter switch of your subwoofer to off. If this cannot be done on your subwoofer, set the

cutoff frequency to a higher value.

! If the speaker distance is not properly set, you may not have a maximized PHASE CONTROL effect.

! The PHASE CONTROL mode cannot be set to ON in the following cases:

— When headphones are plugged in.

— When the PURE DIRECT mode is switched on.

— When the HDMI audio output parameter is set to THROUGH in Setting the Setting the Audio options on page

67.

Better sound using Phase Control and Full Band Phase Control

This receiver is equipped with the two types of functions that correct phase distortion and group delay: Phase

Control and Full Band Phase Control. Activating Full Band Phase Control is strongly recommended because it

also involves the effects of Phase Control.

The Full Band Phase Control feature calibrates the frequency-phase characteristics of the speakers connected.

Standard speakers designed exclusively for audio use generally reproduce sound with the divided frequency

bands output from a speaker system consisting of multiple speakers (in case of typical 3-way speakers, for

instance, the tweeter, the squawker (midrange), and the woofer output sound in the high-, middle-, and low-

frequency ranges, respectively). Though these speakers are designed to flatten the frequency-amplitude charac-

teristics across wide ranges, there are cases where the group delay characteristics are not effectively flattened.

This phase distortion of the speakers subsequently causes group delay (the delay of low-frequency sound against

high-frequency sound) during audio signal playback.

This receiver analyzes the frequency-phase characteristics of the speakers by measuring test signals output from

the speakers with the supplied microphone, therefore flattening the analyzed frequency-phase characteristics

during audio signal playback - the same correction is made for a pair of left and right speakers. This correction

minimizes group delay between the ranges of a speaker and improves the frequency-phase characteristics across

all ranges.

Furthermore, the enhanced frequency-phase characteristics between channels ensure better surround sound

integration for multichannel setting.

% Press PHASE (PHASE CONTROL) to select FULLBAND PHASE.

Both the Phase Control and Full Band Phase Control functions are switched on. The FULL BAND and indica-

tor, on the front panel lights.

Note

! To calibrate and analyze the frequency-phase characteristics of the speakers, either follow the

Full Auto MCACC procedure under Advanced MCACC (see Automatically conducting optimum sound tuning

(Full Auto MCACC) on page 40), or set Auto MCACC menu under Auto MCACC under ADVANCED MCACC to

Full Band Phase Ctrl. Select ALL when you perform the Auto MCACC with Auto MCACC menu. Upon calibra-

tion of the frequency-phase characteristics of the speakers, the Full Band Phase Ctrl feature is automatically

switched on.

! The original characteristics of group delay of the speakers calibrated and the targeted characteristics after

correction can be displayed graphically in the GUI screen (see Checking MCACC Data on page 86). Also, by

transferring the measurement data to the computer using the CD-ROM (AVNavigator), the original characteris-

tics of group delay of the speakers calibrated and the corrected characteristics of group delay can be displayed

in 3-dimension on your PC. For details, refer to the operating instructions for the Advanced MCACC PC Display

Application Software included on the CD-ROM (AVNavigator).

! Depending on the input signal and listening mode, it may not be possible to set the Full Band Phase Ctrl

mode to ON.

! The Full Band Phase Ctrl mode cannot be set to ON in the following cases:

— When headphones are plugged in.

— When the PURE DIRECT mode is switched on.

— When the HDMI audio output parameter is set to THROUGH in Setting the Setting the Audio options on page

67.

Pioneer SC-LX56 Seite 56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SC-LX56

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info