Bedienungsanleitung Pioneer SC-LX58-K (Seite 115 von 140) (Englisch)

577804

115

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

115

FAQ

Symptom Remedy

The maximum volume available

(shown in the front panel display) is

lower than the +12dB maximum.

Check that the Volume Limit is set to OFF (see Volume Setup on page 107 ).

The channel level setting may be over 0.0dB.

Certain listening modes or

HOME MENU items cannot be

selected.

When Operation Mode is set to Basic, the Pioneer-recommended settings are made and

not all of the functions can be used. To use all of the functions without restrictions, set

Operation Mode to Expert (see Operation Mode Setup on page 51 ).

Some functions cannot be selected, depending on the input signal and listening mode.

The volume level drops automati-

cally.

The temperature within the unit has exceeded the allowable value. Try moving the unit for

better ventilation (see Installing the receiver on page 10 ).

Volume seems different when input

is switched.

Set the Channel Level setting to ALL, then adjust the volume of the respective input

sources (see Input Volume Absorber on page 83 ).

When HDZONE is ON, multi-channel

audio sources are not output in the

main zone.

When HDZONE is selected in Speaker System and also the same HDMI input is selected

for both the main zone and HDZONE, 2-channel PCM audio sources are output from the

main zone as well. To output multi-channel audio sources, set HDZONE to OFF or change

the HDZONE input.

No HDZONE sound is output. With HDZONE, multi-channel audio may not be output. In this case, set the audio output

setting of your playback device to 2-channel PCM.

BT AUDIO terminal

Symptom Remedy

The Bluetooth wireless technology

device cannot be connected or oper-

ated. Sound from the Bluetooth wire-

less technology device is not emitted

or the sound is interrupted.

Check that no object that emits electromagnetic waves in the 2.4 GHz band (microwave

oven, wireless LAN device or Bluetooth wireless technology apparatus) is near the unit. If

such an object is near the unit, set the unit far from it. Or, stop using the object emitting

the electromagnetic waves.

Check that the Bluetooth wireless technology device is not too far from the unit and that

obstructions are not set between the Bluetooth wireless technology device and the unit.

Set the Bluetooth wireless technology device and the unit so that the distance between

them is less than about 10 m and no obstructions exist between them.

The Bluetooth wireless technology device may not be set to the communication mode

supporting the Bluetooth wireless technology. Check the setting of the Bluetooth wireless

technology device.

Check that pairing is correct. The pairing setting was deleted from this unit or the Blue-

tooth wireless technology device. Reset the pairing.

Check that the profile is correct. Use a Bluetooth wireless technology device that sup-

ports A2DP profile and AVRCP profile.

Video

Symptom Remedy

No image is output when an input is

selected.

Check the video connections of the source component.

For HDMI, or when V.CONV is set to OFF and a TV and another component are con-

nected with different cords (in Setting the Video options on page 80 ), you must connect

your TV to this receiver using the same type of video cable as you used to connect your

video component. For the component video input, however, signals are only output from

the HDMI OUT 1 or HDMI OUT 2 terminal, so when using the component video input,

set V.CONV to OFF.

Make sure the input assignment is correct for components connected using component

video or HDMI cables (see The Input Setup menu on page 50 ).

Check the video output settings of the source component.

Check that the video input you selected on your TV is correct.

Some components (such as video game units) have resolutions that may not be con-

verted. If adjusting this receiver’s Resolution setting (in Setting the Video options on

page 80 ) and/or the resolution settings on your component or display doesn’t work, try

switching V.CONV (in Setting the Video options on page 80 ) to OFF.

When the device is connected using an HDMI OUT terminal, press the remote con-

trol’s OUT P. button to check the HDMI OUT output setting. For OUT 3, also check the

MAIN/HDZONE setting at ZONE Setup.

When the HDMI OUT 1/2 setting of the output parameter function is set to OFF, set it to

ON.

If HDZONE is set to on, video images connected using a video cable or component cable

are not output from the HDMI terminal. To output video images, turn HDZONE off (page

84 ).

Noisy, intermittent, or distorted

picture.

Sometimes a video deck may output a noisy video signal (during scanning, for example),

or the video quality may just be poor (with some video game units, for example). The

picture quality may also depend on the settings, etc. of your display device. Switch off

the video converter and reconnect the source and display device using the same type of

connection (component or composite), then start playback again.

Video signals are not output from the

component terminal.

When a monitor only compatible with resolutions of 480i is connected to the component

terminal and another monitor is connected to the HDMI terminal, the video signals may

not be output to the monitor connected to the component terminal. If this happens, do

the following:

— Turn off the power of the monitor connected to the HDMI terminal.

— Change the VIDEO P. menu RES setting (see Setting the Video options on page 80 ).

— Video signals from the HDMI terminal cannot be output to the component terminals.

Input the video signals from the player or other source to the composite or component

terminals. When using the component terminal, assign it at Input Setup (see The Input

Setup menu on page 50 ).

The picture’s movement is unnatu-

ral.

When Resolution under VIDEO PARAMETER is set to 1080/24p or 4K/24p, the picture

may not be displayed properly for some source materials. In this case, set the resolution

to something other than 1080/24p or 4K/24p (page 80 ).

Video parameters cannot be used. For audio only input (TUNER, CD, and TV), the video parameter function cannot be used.

Use for video or input with a GUI display.

Cannot be used when the HDZONE is ON. Turn OFF the HDZONE.

Pioneer SC-LX58-K Seite 115

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SC-LX58-K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info