Bedienungsanleitung Pioneer SC-LX58-S (Seite 83 von 140) (Englisch)

577805

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

Using other functions

Notes

! When 7.2ch + Speaker B or 5.2ch + SP-B Bi-Amp is selected for the Speaker System setting (page 102 ) and

Speaker B Link (HDMI Setup on page 74 ) is set to “ON”, the setting of the speaker terminals that are played

changes automatically when HDMI OUT 1 and HDMI OUT 2 are switched. For details, see Switching the

HDMI output on page 83 .

! The subwoofer output depends on the settings you made in Manual speaker setup on page 102 . However, if

SP: B ON is selected above, no sound is heard from the subwoofer (the LFE channel is not downmixed).

! All speaker systems (except 7.2ch + Speaker B connections) are switched off when headphones are

connected.

Switching the HDMI output

Set which terminal to use when outputting video and audio signals from the HDMI output terminals.

The HDMI OUT 1 terminal is compatible with the Control with HDMI function.

1 Press OUT P..

2 Use i/j to select ‘OUT 1/2’.

3 Use k/l to select the output settings for the HDMI OUT 1 and HDMI OUT 2 terminals.

Please wait a while when Please wait ... is displayed.

The output switches among OUT 1+2, OUT 1, OUT 2 and OFF each time the button is pressed.

! The synchronized amp mode is canceled when the HDMI output is switched. If you wish to use the synchro-

nized amp mode, switch to OUT 1, then select the synchronized amp mode on the TV using the TV’s remote

control.

4 Use i/j to select ‘OUT 3’.

5 Use k/l to select the output settings for the HDMI OUT 3 terminal.

Please wait a while when Please wait ... is displayed.

The setting switches between ON and OFF each time this is pressed.

When MAIN/HDZONE is set to HDZONE, the output of the HDMI OUT 3 terminal cannot be switched (page 108 ).

6 When you’re finished, press RETURN.

About the Speaker B Link function

When 7.2ch + Speaker B or 5.2ch + SP-B Bi-Amp is selected for the Speaker System setting (page 102 ) and

Speaker B Link (HDMI Setup on page 74 ) is set to “ON”, the setting of the speaker terminals that are played

changes automatically when HDMI OUT 1 and HDMI OUT 2 are switched. The setting switches as follows.

! OUT 1+2 – Switches to SP: A+B ON. Sound is output simultaneously in the room where the A speakers are

located and in the room where the B speakers are located.

! OUT 1 – Switches to SP: A ON. Sound is only output in the room where the A speakers are located.

! OUT 2 – Switches to SP: B ON. Sound is only output in the room where the B speakers are located.

HDMI 4K/60p signal output setting

If the TV to be connected using HDMI supports 4K/60p, you can switch the 4K/60p signal output setting in accor-

dance with TV performance.

Operation is performed on the front panel of the unit. You cannot perform the setting if the multizone function is

not set to MULTI ZONE OFF (page 84 ).

1 Switch the receiver into standby.

2 While holding down ENTER on the front panel, press u STANDBY/ON.

The display shows RESET c NO d.

3 Use i/j to select ‘4K/60p’.

4 Use k/l to select the signal to set.

! 4:4:4 – Select this setting when connecting to a 4K/60p 4:4:4 24 bit compatible TV using HDMI. More high

quality video images can be enjoyed.

— When the HDMI cable does not support 4K/60p 4:4:4 24 bit (18 Gbps transmission), video image may not

be output properly. In that case, select 4:2:0 to watch a 4K/60p 4:2:0 24 bit video image.

— The HDMI OUT 3 terminal does not output a 4K/60p 4:4:4 24 bit video image if MAIN/HDZONE is set to

HDZONE.

! 4:2:0 – Select this setting when connecting to a 4K/60p 4:2:0 24 bit compatible TV using HDMI.

5 When you’re finished, press RETURN.

6 Press u STANDBY/ON to switch on the receiver and your TV.

Make sure that the TV’s video input is set to this receiver.

Changing the channel level while listening

Using the channel level settings, you can adjust the overall balance of your speaker system, an important factor

when setting up a home theater system.

1 Press CH LV..

2 Use i/j to select the channel you wish to adjust.

3 Adjust the volume using k/l.

The volume can be adjusted in the range of -12.0dB to +12.0dB, 0.5 dB steps.

4 When you’re finished, press RETURN.

Input Volume Absorber

This can be used to correct for the difference in volume between input sources.

1 Switch to the input whose volume you want to adjust.

2 Press CH LV..

3 Use i/j to select ‘ALL’.

4 Adjust the volume using k/l.

The volume can be adjusted in the range of -12.0dB to +12.0dB, 0.5 dB steps.

5 When you’re finished, press RETURN.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer SC-LX58-S Seite 83

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SC-LX58-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info