Bedienungsanleitung Pioneer SC-LX58-S (Seite 103 von 140) (Englisch)

577805

103

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

103

The System Setup and Other Setup menus

! 5.2 +ZONE 2+HDZONE – Select to use the surround back (ZONE 2) and front wide (HDZONE) speaker termi-

nals for an independent systems in another zone (see Using the MULTI-ZONE controls on page 84 ).

! 5.2ch + SP-B Bi-Amp – Select this setting if you’re bi-amping your B speakers (see Bi-amping your speakers

on page 25 ).

! 5.2ch F+Surr Bi-Amp – Select this setting if you’re bi-amping your front and surround speakers (see

Bi-amping your speakers on page 25 ).

! 5.2ch F+C Bi-Amp – Select this setting if you’re bi-amping your front and center speakers (see Bi-amping

your speakers on page 25 ).

! 5.2ch C+Surr Bi-Amp – Select this setting if you’re bi-amping your center and surround speakers (see

Bi-amping your speakers on page 25 ).

! Multi-ZONE Music – See Using Multi-ZONE Music on page 103 .

3 If you selected 7.2.2ch TMd/FW, 7.2.2ch TMd/FH, 7.2ch + Speaker B, 7.2ch + Front Bi-Amp,

or 7.2ch + HDZONE in Step 2, select the placement of the surround speakers.

In a 7.2-channel surround system with surround speakers placed directly at the sides of the listening position,

the surround sound of 5.1-channel sources is heard from the side. This function mixes the sound of the surround

speakers with the surround back speakers so that the surround sound is heard from diagonally to the rear as it

should be.

Depending on the positions of the speakers and the sound source, in some cases it may not be possible to

achieve good results. In this case, set the setting to ON SIDE or IN REAR.

! ON SIDE – Select when the surround speakers is positioned right beside you.

! IN REAR – Select when the surround speaker is positioned obliquely behind you.

4 When ‘Setting Change?’ is displayed, select Yes.

If No is selected, the setting is not changed.

You will return to the Manual SP Setup menu.

Using Multi-ZONE Music

Multi-ZONE Music can be used to play the same sound in the MAIN ZONE, ZONE 2 and ZONE 3, for example for

home parties. Normally set Speaker System to 5.2 +ZONE 2+ZONE 3 for multi-zone/multi-source playback, then

switch it to Multi-ZONE Music when having a home party. When this is done, the sound of the input function

selected for the MAIN ZONE is played in all zones (the MAIN ZONE, ZONE 2 and ZONE 3).

! There is virtually no delay in the sound.

! Switching of the input for only ZONE 2 or ZONE 3 is disabled, but the volume can be adjusted or muted for the

individual zones.

! This is only valid for ZONE 2 and ZONE 3 connections using the speaker terminals. No sound is output from the

ZONE 2 and ZONE 3 pre-out terminals. Nothing is output from the ZONE 2 and ZONE 3 COMPONENT VIDEO

output and VIDEO output terminals.

! The HDZONE setting does not apply to Multi-ZONE Music.

Speaker Setting

Use this setting to specify your speaker configuration (size, number of speakers and crossover frequency). It

is a good idea to make sure that the settings made in Automatically conducting optimum sound tuning (Full

Auto MCACC) on page 48 are correct. Note that this setting applies to all MCACC presets, and cannot be set

independently.

1 Select ‘Speaker Setting’ from the Manual SP Setup menu.

2 Choose the set of speakers that you want to set, then select a speaker size.

Use k/l to select the size (and number) of each of the following speakers:

! Front – Select LARGE if your front speakers reproduce bass frequencies effectively, or if you didn’t connect a

subwoofer. Select SMALL to send the bass frequencies to the subwoofer.

! Center – Select LARGE if your center speaker reproduces bass frequencies effectively, or select SMALL to

send bass frequencies to the other speakers or subwoofer. If you didn’t connect a center speaker, choose NO

(the center channel is sent to the front speakers).

! TMd – Select LARGE if your top middle speakers reproduce bass frequencies effectively, or select SMALL

to send bass frequencies to the other speakers or subwoofer. When Dolby Enabled Speaker is used, select

Dolby Sp (page 23 ). If you didn’t connect the top middle speakers, choose NO (the top middle channel is

sent to the front speakers).

— You can adjust this setting only when Speaker System setting is 7.2.2ch TMd/FW, 7.2.2ch TMd/FH,

5.2.4ch or 7.2ch + Speaker B.

— If you change the setting from Dolby Sp to SMALL or LARGE, the set value for Speaker Distance

may be changed. This is because the maximum value of Speaker Distance when set to Dolby Sp is

bigger than the maximum value of Speaker Distance when set to SMALL and LARGE. If the value of

Speaker Distance set to Dolby Sp exceeds the maximum value of Speaker Distance for SMALL and

LARGE, Speaker Distance for SMALL and LARGE is set to its maximum value.

! TFw – Select LARGE if your top forward speakers reproduce bass frequencies effectively, or select SMALL

to send bass frequencies to the other speakers or subwoofer. When Dolby Enabled Speaker is used, select

Dolby Sp (page 23 ). If you didn’t connect the top forward speakers, choose NO (the top forward channel is

sent to the front speakers).

— You can adjust this setting only when Speaker System setting is 5.2.4ch.

— When you set TBw to NO, this setting is automatically set to NO.

— If you change the setting from Dolby Sp to SMALL or LARGE, the set value for Speaker Distance

may be changed. This is because the maximum value of Speaker Distance when set to Dolby Sp is

bigger than the maximum value of Speaker Distance when set to SMALL and LARGE. If the value of

Speaker Distance set to Dolby Sp exceeds the maximum value of Speaker Distance for SMALL and

LARGE, Speaker Distance for SMALL and LARGE is set to its maximum value.

! TBw – Select LARGE if your top backward speakers reproduce bass frequencies effectively, or select SMALL

to send bass frequencies to the other speakers or subwoofer. When Dolby Enabled Speaker is used, select

Dolby Sp (page 23 ). If you didn’t connect the top backward speakers, choose NO (the top backward chan-

nel is sent to the front speakers).

— You can adjust this setting only when Speaker System setting is 5.2.4ch.

— When you set TFw to NO, this setting is automatically set to NO.

— If you change the setting from Dolby Sp to SMALL or LARGE, the set value for Speaker Distance

may be changed. This is because the maximum value of Speaker Distance when set to Dolby Sp is

bigger than the maximum value of Speaker Distance when set to SMALL and LARGE. If the value of

Speaker Distance set to Dolby Sp exceeds the maximum value of Speaker Distance for SMALL and

LARGE, Speaker Distance for SMALL and LARGE is set to its maximum value.

Pioneer SC-LX58-S Seite 103

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SC-LX58-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info