Bedienungsanleitung Pioneer SC-LX704 (Seite 14 von 223) (Englisch)

699655

Zoom out

Zoom in

Vorherige Seite

1/223

Nächste Seite

Contents

≫

Connections

≫

Playback

≫

Setup

≫

Front Panel≫ Rear Panel≫ Remote≫

1. COMPONENT VIDEO IN jacks: Input the AV component video signals with a

component video cable. (Compatible only with 480i or 576i resolution.)

2. Wireless antenna: Used for Wi-Fi connection or when using a BLUETOOTH

enabled device. Adjust their angles according to the connection status.

3. VIDEO IN jacks: Input the AV component video signals with an analog video

cable.

AUDIO IN jacks: Input AV component audio signal with an analog audio cable.

5. HDMI IN jacks: Transmit video signals and audio signals with a HDMI cable

connected to an AV component.

6. SIGNAL GND terminal: The ground wire of the turntable is connected.

7. HDMI OUT jacks: Transmit video signals and audio signals with an HDMI

cable connected to a monitor such as a TV or projector.

8. USB port: A USB storage device is connected so that music les stored in it

can be played. ( p104)

You can also supply power (5 V/0.5 A) to USB devices with a USB cable.

9. NETWORK port: Connect to the network with a LAN cable.

10.

DIGITAL AUDIO IN OPTICAL/COAXIAL jacks: Input TV or AV component

digital audio signals with a digital optical cable or digital coaxial cable.

11.

AC IN: The supplied power cord is connected.

12.

RS-232C port: Connect a home control system equipped with an RS-232C

port. For adopting a home control system, contact the specialized stores.

13.

ANTENNA AM LOOP/FM UNBAL 75 Ω terminal: The supplied antennas are

connected.

14.

IR IN/OUT port: Connect a remote control receiver unit. ( p91)

15.

ZONE 2 PRE/LINE OUT jacks: Output audio signals with an analog audio

cable connected to a pre-main amplier or a power amplier in a separate

room (ZONE 2).

ZONE B LINE OUT jacks: Connect to a pre-main amplier with an analog

audio cable, and simultaneously output audio of the same source as that of

the speakers (ZONE A) connected to this unit.

16.

ZONE 3 PRE/LINE OUT jacks: Output audio signals with an analog audio

cable connected to a pre-main amplier or a power amplier in a separate

room (ZONE 3).

17.

12V TRIGGER OUT A/B jack: Connect a device equipped with a 12V trigger

input jack to enable power link operation between the device and this unit.

( p92)

18.

SPEAKERS terminals: Connect speakers with speaker cables. (North

American models support banana plugs. Use a plug 4 mm in diameter. Y plug

connection is not supported.)

19.

SUBWOOFER PRE OUT jack: Connect a powered subwoofer with a

subwoofer cable. Up to two powered subwoofers can be connected. You can

set the volume levels of the 2 powered subwoofers to different levels.

( p163)

20.

PRE OUT jacks: Connect a power amplier. ( p75)

21.

VOLTAGE SELECTOR (multi-voltage models): Use a medium-sized

screwdriver to switch the voltage to the one appropriate for your region. Before

changing the voltage, rst disconnect the power cord.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer SC-LX704 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SC-LX704

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info