Bedienungsanleitung Pioneer SC-LX704 (Seite 197 von 223) (Englisch)

699655

197

Zoom out

Zoom in

Vorherige Seite

1/223

Nächste Seite

197

Front Panel≫ Rear Panel≫ Remote≫

Contents

≫

Connections

≫

Playback

≫

Setup

≫

analog or DSD.

Audio Return Channel: You can enjoy the sound of the HDMI-connected ARC-

compatible TV through the speakers connected to the unit. Select "On" when

listening to the audio of TV using the speakers of this unit. Select "Off" when the

ARC function is not used.

 Audio

Sound Retriever: Improve the quality of the compressed audio. Playback sound

of lossy compressed les such as MP3 will be improved. The setting can be

separately set to each input selector. The setting is effective in the signals of

48 kHz or less. The setting is not effective in the bitstream signals.

• It cannot be set if the listening mode is Direct or Pure Direct.

Midnight: Make small sounds easily heard. It is useful when you need to reduce

the volume while watching a movie late night. You can enjoy the effect only when

playing Dolby series and DTS series input signals.

• It cannot be set if the listening mode is Direct or Pure Direct.

• The setting cannot be used in the following cases.

– If "Loudness Management" is set to "Off" when playing Dolby Digital Plus or

Dolby TrueHD

– When the input signal is DTS:X and "Dialog Control" is other than 0 dB

Stereo Assign: When the listening mode is set to "Stereo", the audio output

destination can be set to "Surround", "Surround Back", "Height 1" or "Height 2" in

addition to the normal right and left channels ("Front") of front speakers.

• The setting cannot be used in the following cases.

– When a listening mode other than “Stereo” is set

– When using Speaker B

• It is not possible to select speakers that are not set at "System Setup" -

"Speaker" - "Conguration" on the Home screen.

Zone B: Select a method of outputting audio to ZONE B from among "Off",

"On(A+B)" and "On(B)".

• In the following cases, "Zone B" cannot be selected.

– When ZONE 2 is On

– When "System Setup" - "Speaker" - "Conguration" - "Zone 2 Preout" on

the Home screen is set to "Zone 2" (

p160)

Speakers: When Speaker B are used, you switch output between Speaker A/B/

A+B.

• Note that sound is not output from the surround back speaker during Speaker

A+B output.

Auto Phase Control+: The low frequencies are recorded with a delay for some

discs not made according to phase control standards. This function corrects the

phase shift when playing such discs. When "Auto" is selected, in addition to the

low frequency delay, the polarity and correlation are also detected and corrected.

• It cannot be set if the listening mode is Pure Direct.

Dialog Lifted Up : By adjusting the localization of the center elements, you can

make it easier to hear dialog in movies or give more prominence to the vocals in

music. If you are using front high speakers, you can select from "1" (low) to "4"

(high).

• The function cannot be set in the following cases.

– When the Front High speakers are not enabled

– When the “Adjusting DIALOG” (

p130) function is being used

– When “Dialog Control” ( p164) has been set

– When the listening mode is Direct or Pure Direct

Audio Scaler : By selecting "Auto", "Hi-bit 32", "Upsampling", and "Digital Filter"

are each automatically set to the optimum values so that you get the high-quality

playback of music les and CDs. The setting can be separately set to each input

selector.

Select "Manual" if you want to manually adjust "Hi-bit 32", "Upsampling", and

"Digital Filter".

Hi-bit 32 : By expanding the dynamic range of digital audio signal sources such

as CDs, DVDs, and BDs, it is possible to achieve a smoother and more rened

sound. The setting can be separately set to each input selector. This can be set

when the sampling frequency is 44.1 kHz or more.

• This cannot be set if "Auto" is selected for "Audio Scalar".

Upsampling : By increasing the sampling frequency of PCM 2 channel audio by

a factor of 2 or 4, you can achieve high-quality sound reproduction. The setting

can be separately set to each input selector. This can be set when the sampling

frequency is between 44.1 kHz and 96 kHz. This function works in the Direct,

Pure Direct, and Stereo listening modes.

• This cannot be set if "Auto" is selected for "Audio Scalar".

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer SC-LX704 Seite 197

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SC-LX704

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info