Bedienungsanleitung Pioneer SC-LX86 (Seite 110 von 133) (Englisch)

488896

110

Zoom out

Zoom in

Vorherige Seite

1/133

Nächste Seite

110

FAQ

Symptom Causes Remedy

AVNavigator does not inter-

act well with the receiver.

The receiver’s power is not turned

on.

Turn the receiver’s power on. (Wait about 60 seconds after

the power turns on for network functions to start.)

After this, press Detection in AVNavigator to redetect the

receiver.

The receiver or computer is not con-

nected to the LAN.

Connect a LAN cable to the receiver or computer (page 39).

After this, press Detection in AVNavigator to redetect the

receiver.

The router’s power is off. Turn the router’s power on.

After this, press Detection in AVNavigator to redetect the

receiver.

AVNavigator’s network settings are

not correct.

If your router does not support DHCP or UPnP, the receiv-

er’s IP address must be set in AVNavigator. First set the

IP address on the receiver, then set the same address in

AVNavigator (page 99).

After this, press Detection in AVNavigator to redetect the

receiver.

Network connections could be

restricted due to the computer’s net-

work settings, security settings, etc.

Check the computer’s network settings, security settings,

etc.

After this, press Detection in AVNavigator to redetect the

receiver.

When the operating instructions

interactive mode is changed, the

settings may not be transferred to

the browser, causing AVNavigator to

stop interacting.

Either refresh the page’s display using the browser’s

refresh button or display a different page from the links so

that the setting is transferred.

When the

Wiring Navi, Operation Guide,

Interactive Manual, Glossary

or Software Update is

launched, a warning about

security protection appears

on the browser.

This is because of the browser’s

security function.

This is not a problem. Perform the operation to authorize

the blocked contents.

Operation Guide does not

display properly.

Adobe Flash Player 10 is not

installed, or its version is too old.

Download Adobe Flash Player from the Adobe site (http://

www.adobe.com/downloads/). If your version is old, update

it.

Software updating does not

operate well.

There may be a problem with your

Internet Service Provider’s network.

Contact your contracted provider.

USB interface

Symptoms Causes Remedies

The folders/files stored on a

USB memory device are not

displayed.

The folders/files are currently stored

in a region other than the FAT (File

Allocation Table) region.

Store the folders/files in the FAT region.

The number of levels in a folder is

more than 9.

Limit the maximum number of levels in a folder to 9 (page

51).

The audio files are copyrighted.

Copyrighted audio files stored on a USB memory device

cannot be played back (page 51).

Symptoms Causes Remedies

A USB memory device is

not recognized.

The USB memory device does not

support the mass storage class

specifications.

Try using a USB memory device compatible with the mass

storage class specifications. Note that there are cases

where even the audio files stored on a USB memory device

compatible with the mass storage class specifications are

not played back on this receiver (page 51).

Connect the USB memory device and switch on this

receiver (page 40).

A USB hub is currently being used.

This receiver does not support USB hubs (page 51).

This receiver recognizes the USB

memory device as a fraud.

Switch off and on again this receiver.

Reconnect the USB device with the receiver switched off.

Change to an input other than iPod/USB, then set the input

back to iPod/USB.

A USB memory device is

connected and displayed,

but the audio files stored

on the USB memory device

cannot be played back.

Some formats of USB memory

devices, including FAT 12, NTFS, and

HFS, cannot be played back on this

receiver.

Check whether the format of your USB memory device is

either FAT 16 or FAT 32. Note that the FAT 12, NTFS, and

HFS formats cannot be played back on this receiver (page

51).

The file format cannot be properly

played back on this receiver.

See the list of file formats that can be played back on this

receiver (page 52).

iPod

Symptoms Causes Remedies

iPod is not recognized. This receiver recognizes the iPod as

a fraud.

Switch off and on again this receiver.

Reconnect the iPod with the receiver switched off.

Change to an input other than iPod/USB, then set the input

back to iPod/USB.

Network Standby is set to ON.

Set Network Standby to OFF, turn off the receiver’s

power, turn the power back on, then connect the iPod

(page 100).

Network

Symptoms Causes Remedies

Cannot access the network. The LAN cable is not firmly con-

nected.

Firmly connect the LAN cable (page 39).

The router is not switched on. Switch on the router.

Internet security software is cur-

rently installed in the connected

component.

There are cases where a component with Internet security

software installed cannot be accessed.

The audio component on the net-

work which has been switched off is

switched on.

Switch on the audio component on the network before

switching on this receiver.

Playback does not start

while “Connecting...” con-

tinues to be displayed.

The component is currently discon-

nected from this receiver or the

power supply.

Check whether the component is properly connected to

this receiver or the power supply.

Pioneer SC-LX86 Seite 110

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SC-LX86

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info