Bedienungsanleitung Pioneer SC-LX904 (Seite 200 von 225) (Englisch)

699654

200

Zoom out

Zoom in

Vorherige Seite

1/225

Nächste Seite

200

Front Panel≫ Rear Panel≫ Remote≫

Contents

≫

Connections

≫

Playback

≫

Setup

≫

(digital analog converter). You can choose "Slow" (gives the sound a soft and

uid feel), "Sharp" (gives the sound more structure and rmer feel), or "Short"

(gives the sound a feeling of a quick start and moving forward). The setting can

be separately set to each input selector. This can be set when the sampling

frequency is 44.1 kHz or more.

• This cannot be set if "Auto" is selected for "Audio Scalar".

Reex Optimizer : Enhance the reection effect of Dolby enabled speakers from

the ceiling.

• This setting can be selected when "System Setup" - "Speaker" -

"Conguration" - "Height 1 Speaker"/"Height 2 Speaker" is set to "Dolby

Speaker".

• It cannot be set if the listening mode is Pure Direct.

 MCACC

MCACC EQ: Enable or disable the equalizer function that corrects for distortion

caused by the acoustic environment of the room.

• It cannot be set if the listening mode is Pure Direct.

Phase Control: Correct phase disturbance in the low range to enhance the bass.

This enables you to achieve powerful bass reproduction that is faithful to the

original sound.

• It cannot be set if the listening mode is Pure Direct.

When "Phase Control" is set to "Full Band":

Along with the Phase Control function, the Full Band Phase Control function is

also enabled. The Full Band Phase Control function corrects for group delay (the

difference between phase and timing) between speakers when speaker units are

divided into multiple parts, such as tweeter and woofer sections, and furthermore

it lines up the phases of the connected speakers so the unit can achieve more

accurate reproduction across the full range (full band) and across all channels.

Furthermore, if the "Front Align" calibration type has been selected and Full Auto

MCACC was performed, the phases of speakers other than the front speakers

are corrected to match the frequency phase characteristics of the front speakers.

• "Full Band" cannot be selected if Full Auto MCACC has not been performed.

MCACC Memory : From MCACC Memory 1 to 3 where speaker settings

calibrated with "Full Auto MCACC" or "Manual MCACC" are saved, select which

Memory to use.

Theater Filter: Adjust the soundtrack that was processed to enhance its high

pitch range, in order to make it suitable for home theater.

• It cannot be set if the listening mode is Direct or Pure Direct.

Standing Wave: Setting this "On" will control the effect of the standing wave

generated by the sound wave reected by wall or similar interfering with the

original sound wave.

• It cannot be set if the listening mode is Pure Direct.

 Level

Front: Adjust the speaker level of the front speaker while listening to the sound.

Center: Adjust the speaker level of the center speaker while listening to the

sound.

Subwoofer 1 / Subwoofer 2 : Adjust the speaker level of the subwoofer while

listening to the sound.

• If you set the unit to the standby mode, the adjustments you made will be

restored to the previous statuses.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer SC-LX904 Seite 200

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SC-LX904

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info