Bedienungsanleitung Pioneer SC-LX904 (Seite 203 von 225) (Englisch)

699654

203

Zoom out

Zoom in

Vorherige Seite

1/225

Nächste Seite

203

Front Panel≫ Rear Panel≫ Remote≫

Contents

≫

Connections

≫

Playback

≫

Setup

≫

 1. Speaker Setup

1. Select the connected speaker conguration, and press ENTER.

Note that the image on the screen changes each time you select the number

of channels in "Speaker Channels".

Speaker Setup

Height 1 Speaker

Height 2 Speaker

Top Front

Top Rear

2 ch

Speaker B

Zone 2 Preout

Zone 2

7.1.4 ch

Zone Speaker

Set the items on the second page with the cursor buttons / . Here you

can save the measurement results for each speaker measured in "2.Full Auto

MCACC" in the following 3 calibration types. Use / to select the memory

location you want to save the results of the measurement to by item. If multiple

calibration types are selected, you can select the calibration type to use in "AV

Adjust" - "MCACC" - "MCACC Memory". Note that you cannot select the same

save destination for different calibration types.

Symmetry (default value: M1.Memory 1): Calibration that emphasizes phase

characteristics

All Channel Adjust (default value: ---): Calibration that emphasizes

frequency characteristics

Front Align (default value: ---): Calibration that emphasizes front speaker

characteristics

Press ENTER when you have nished the settings.

Speaker Setup

Front Align

All Channel Adjust

Symmetry

Select where the data is to be stored.

Calibrates with emphasis on phase characteriscs.

---

M1.Memory 1

2. The speaker combination selected in step 1 is displayed. "Yes" is displayed for

the selected speakers. If the setting is correct, press ENTER.

3. Select "Next" and press ENTER. Then a test tone is output from each speaker

to conrm the connection. Selecting each speaker with the cursors / will

output the test tone. Press ENTER after conrmation.

4. If there is no problem with the speaker connection, select "Next" and press

ENTER. To return to "Speaker Setup", select "Back to Speaker Setup" and

press ENTER.

 2. Full Auto MCACC

Place the supplied speaker setup microphone in the listening position, measure

the test tones emitted by the speakers, then the unit automatically sets the

optimum volume level for each speaker, the crossover frequencies, and the

distance from the listening position. The inuence of standing waves can be

reduced to suit the listening environment, the reverberation characteristics can be

measured to increase the precision of calibration, the speaker equalizers can be

adjusted, and the difference in phase and timing between speakers and speaker

units can be corrected. These settings and calibrations can be readjusted with

Manual MCACC, and you can enable or disable them in AV Adjust.

• It takes between 3 and 12 minutes for calibration to be completed. Each

speaker outputs the test tone at high volume during measurement, so be

careful of your surroundings. Also, keep the room as quiet as possible during

measurement.

• If you connect a subwoofer, check the power and volume of the subwoofer.

Set the subwoofer volume to more than half.

• If the power of this unit suddenly turns off, the wires in the speaker cables

have touched the rear panel or other wires, and the protection circuit is

working. Twist the wires again securely, and make sure they do not stick out of

the speaker terminals when connecting.

1. Place the supplied speaker setup microphone at the listening position, and

connect it to the SETUP MIC jack on the main unit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer SC-LX904 Seite 203

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SC-LX904

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info