Bedienungsanleitung Pioneer SX-20-S (Seite 5 von 15) (Englisch)

491891

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

Connecting up 02

Chapter 2:

Connecting up

Making cable connections

CAUTION

• Before making or changing the connections, switch off the power and disconnect the power cord from the AC

outlet.

• Connect the power cord after all the connections between devices have been completed.

5(&

3/$<

AC IN

SPEAKERS

RECORDER

INININ

AM LOOP

SIGNAL

GND

FM UNBAL

OUT

PHONO

(

)

ANTENNA

SACD/CD

NETWORK

SACD/CD player

Network audio player

Speaker system B

Speaker system A

Turntable

FM/AM antennas

(see page 6)

CD recorder or

Cassette deck

Right Left

Right

Left

Power cord

(included)

Important

•The SIGNAL GND terminal is provided to reduce

noise when connecting the unit to components

such as an analog turntable.

• Do not connect the PHONO (MM) terminals to any

component other than a turntable; also, do not

connect to a turntable equipped with built-in

equalizer. An excessively high sound output may be

produced, resulting in damage to your speakers or

other devices.

• The unit’s PHONO (MM) terminals are designed to

be used with turntables equipped with MM

(moving-magnet) type cartridges. Turntables

equipped with MC (moving-coil) cartridges cannot

be used.

• Make sure not to bend the cables over the top of

this unit (as shown in the illustration). If this

happens, the magnetic field produced by the

transformers in this unit may cause a humming

noise from the speakers.

• If your turntable has a grounding wire, secure it to

the ground terminal on this receiver.

Note

• When connecting a tape cassette deck, playback

noise may be heard, depending on the installation

location. This noise is caused by leakage flux from

the receiver’s transformer. In this event, change the

installation location, or move the deck farther from

the receiver.

Connecting audio cables

Connect the white plug to the left (L) jack, and the red

plug to the right (R) jack. Be sure to insert the plugs fully

into the jacks.

Connecting speaker cables

1 Twist the cable cores.

2 Loosen the nut on the

SPEAKERS

terminal, and insert the speaker cable into

the exposed hole in the terminal shaft.

3 Retighten the terminal nut.

CAUTION

• When using only one set of speaker terminals

(SPEAKERS A or SPEAKERS B), the speaker used

should have a nominal impedance between 4 Ω

and 16 Ω. When using both sets of terminals,

the connected speakers should have nominal

impedance between 8 Ω and 16 Ω. Consult the

instructions accompanying your speakers for

details regarding the impedance value.

• Make sure the positive and negative (+/–) terminals

on the receiver match those on the speakers.

• These speaker terminals carry HAZARDOUS live

voltage. To prevent the risk of electric shock when

connecting or disconnecting the speaker cables,

disconnect the power cord before touching any

uninsulated parts.

• Make sure that all the bare speaker wire is twisted

together and inserted fully into the speaker

terminal. If any of the bare speaker wire touches the

back panel it may cause the power to cut off as a

safety measure.

Left (white)

Right (red)

12 3

10 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer SX-20-S Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SX-20-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info