Bedienungsanleitung Pioneer SX-20-S (Seite 3 von 28) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

491891

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

English

Français

Italiano

Español

Nederlands

Deutsch

Connecting up (continued)

VENTILATION CAUTION

When installing this unit, make sure to leave space around the unit for

ventilation to improve heat radiation (at least 40 cm at top, 10 cm at rear,

and 20 cm at each side).

WARNING

Slots and openings in the cabinet are provided for ventilation to ensure

reliable operation of the product, and to protect it from overheating. To

prevent fire hazard, the openings should never be blocked or covered with

items (such as newspapers, table-cloths, curtains) or by operating the

equipment on thick carpet or a bed.

D3-4-2-1-7b*_A1_En

STEREO RECEIVER

VOLUME

TUNE

PRESET

MEMORY

STANDBY

SPEAKERS

PHONES

TONE

BALANCE

STANDBY

Connecting the speakers

Make sure you connect the speaker on the right to the right (R) terminal

and the speaker on the left to the left (L) terminal. Also make sure the

positive and negative (+/–) terminals on the receiver match those on the

speakers.

Twist the cable cores.

Loosen the nut on the SPEAKERS terminal, and insert the speaker

cable into the exposed hole in the terminal shaft.

Retighten the terminal nut.

12 3

10 mm

CAUTION

•

When using only one set of speaker terminals (SPEAKERS A or

SPEAKERS B), the speaker used should have a nominal impedance

between 4

and 16

. When using both sets of terminals, the

connected speakers should have nominal impedance between 8

and 16

. Consult the instructions accompanying your speakers

for details regarding the impedance value.

•These speaker terminals carry

HAZARDOUS live voltage

. To prevent

the risk of electric shock when connecting or disconnecting the

speaker cables, disconnect the power cord before touching any

uninsulated parts.

Connecting the FM and AM antennas

Connect FM wire antenna and the the AM loop antenna

as shown below.

AM LOOP

FM UNBAL

ANTENNA

To power outlet

Connecting your equipment

Connecting the playback components

Connect the audio outputs of your SACD player (or CD player) to the

SACD/CD IN jacks on this receiver.

Connect the audio outputs of your network audio player to the

NETWORK IN jacks on this receiver.

•You may connect other audio components furnished with analog audio

output jacks. If you wish to connect a portable audio player or other

component furnished with mini-plug output jacks (or headphone jacks),

use of a commercially available conversion plug will be necessary.

Connecting the cassette deck



Connect the audio outputs of your cassette deck (or other recorder)

to the RECORDER IN jacks on this receiver. Then connect the audio

inputs on the cassette deck to the RECORDER OUT jacks on this

receiver.

This will allow you to make recordings from the components connected to

this receiver.

Connecting a turntable



Connect the audio outputs of your turntable to the PHONO IN jacks

on this receiver.

Important

•The

SIGNAL GND

terminal is provided to reduce noise when

connecting the unit to components such as an analog turntable.

•Do not connect the

PHONO (MM)

terminals to any component other

than a turntable; also, do not connect to a turntable equipped with

built-in equalizer. An excessively high sound output may be produced,

resulting in damage to your speakers or other devices.

•The unit’s

PHONO (MM)

terminals are designed to be used with

turntables equipped with MM (moving-magnet) type cartridges.

Turntables equipped with MC (moving-coil) cartridges cannot be used.

Plugging the receiver

Only plug in after you have connected all your components to this receiver,

including the speakers.

Plug the supplied power cord into the AC IN socket on the back of

the receiver.

Plug the other end into a power outlet.

AC IN

CAUTION

•Handle the power cord by the plug part. Do not pull out the plug by

tugging the cord, and never touch the power cord when your hands are

wet, as this could cause a short circuit or electric shock. Do not place

the unit, a piece of furniture, or other object on the power cord or pinch

the cord in any other way. Never make a knot in the cord or tie it with

other cables. The power cords should be routed so that they are not

likely to be stepped on. A damaged power cord can cause a fire or give

you an electric shock. Check the power cord once in a while. If you find

it damaged, ask your nearest Pioneer authorized independent service

company for a replacement.

SX-20_YXE8_book.indb 3SX-20_YXE8_book.indb 3 2012/08/03 9:33:402012/08/03 9:33:40

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer SX-20-S Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SX-20-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info