Bedienungsanleitung Pioneer SX-315 (Seite 17 von 52) (Englisch, Französisch)

626471

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Surround sound setup

English

•

Room L

– Larger than average room (approx. 7.5 x

9.0m)

4 Use the ROOM SETUP button to select a seating

position setting, then press ENTER.

Select from:

•

Seat Fwd

– If you are nearer to the front speakers

than the surround speakers

•

Seat Mid

– If you are equal distance from the front

and surround speakers

•

Seat Back

– If you are nearer to the surround

speakers than the front speakers

After selecting the seating position, the display shows

the new settings for a couple of seconds.

Setting speaker distances

For more accurate surround sound settings you can set

the distance from your listening position to each of the

speakers.

See also

Setting individual channel levels

below for

setting the relative levels of individual speakers.

1 Press SYSTEM SETUP (front panel or remote).

The display shows:

F c h :

followed by a distance in feet.

This is the receiver’s current setting for the distance from

your listening position to each of the front left and right

speakers.

2 Use the

/

(cursor left/right) buttons to

change the distance setting.

You can set the distance in increments of one foot.

• You can also use the

and

buttons on the front

panel.

3 Press SYSTEM SETUP again to select the center

speaker distance setting, then set using the

/

(cursor left/right) buttons.

The display shows:

C c h :

followed by the current

distance setting.

4 Press SYSTEM SETUP again to select the suround

speaker distance setting, then set using the

/

(cursor left/right) buttons.

The display shows:

S c h :

followed by the current

distance setting.

5 Press SYSTEM SETUP again to select the

subwoofer speaker distance setting, then set using

the

/

(cursor left/right) buttons.

The display shows:

S W :

followed by the current distance

setting.

6 Press ENTER to exit the System Setup menu.

Setting individual channel levels

In order to balance the sound from all the speakers in

your system you can adjust the relative level of each

speaker. Adjust so that the level of each speaker is

similar from your listening position.

While setting the channel levels, you can either listen to

a multichannel source (such as a DVD), or use the built-

in test tone feature.

Setting the channel levels using the test tone

The test tone feature outputs a constant noise tone from

each speaker, giving you a good reference to adjust the

levels.

1 Press TEST TONE.

The test tone starts sounding from the left front speaker

and continues around each speaker in turn.

2 While the test tone is sounding, use the

/

(cursor left/right) buttons to adjust the level of that

speaker.

You can adjust each speaker from

–10

(quieter) to

+10

(louder).

• You can also use the front panel

and

buttons,

although it’s usually best to make this setting from

your listening position using the remote.

3 When you’re done, press ENTER to exit.

• Pressing any button (except

VOLUME +/–

) will also

exit.

SYSTEM

SETUP

ENTER

TEST

TONE

ENTER

SX-315.book 17 ページ２００４年１１月８日　月曜日　午前１１時２分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer SX-315 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info