Bedienungsanleitung Pioneer SX-N30AE (Seite 29 von 124) (Englisch, Französisch, Spanisch)

699652

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

> Before Start > Part Names > Install > Initial Setup > Playback

Supplementary information | Advanced Setup |Others

4. Source

5. Network

0 When LAN is configured with a DHCP, set "DHCP" to "Enable" to configure the setting

automatically. Further, to assign fixed IP addresses to each component, you must set

"DHCP" to "Disable" and assign an address to this unit in "IP Address" as well as set

information related to your LAN, such as Subnet Mask and Gateway.

Opt Wakeup When an audio signal is input through the OPTICAL terminal

while this unit is in standby, this feature automatically detects it.

"On ": This unit is turned on and outputs the audio.

"Off (default value)": The function is disabled.

0 When a cable is connected to the OPTICAL terminal and this

setting is enabled, power consumption increases even when

the unit is on standby, however, the increase in power

consumption is kept to a minimum by automatically entering

the HYBRID STANDBY mode, where only essential circuits

are operating.

AM Freq Select a frequency step depending on your area of residence.

Select "9 kHz (default value)" or "10 kHz".

0 When this setting is changed, all radio presets are deleted.

Vol Abs Adjust the volume level difference between the devices

connected to the unit. Select the input selector to configure.

Select from "-12 dB" to "+12 dB". Set a negative (j) value if the

volume of the target device is larger than the others and a

positive (i) value if smaller. To check the audio, start playback of

the connected device. (Default Value is "0.0 dB")

Name Edit Set an easy name to each input. The set name will be shown on

the main unit display. Select the input selector to configure.

For details on how to enter text, refer to "Entering text" (P14).

0 To name a preset radio station, press TUNER on the remote

controller, select AM/FM and select the preset number.

0 It cannot be set if the "NET" or "BLUETOOTH" input is

selected.

Wi-Fi Connect the unit to network via wireless LAN router.

"On": Wireless LAN connection

"Off (default value)": To connect via wired LAN

Wi-Fi Setup You can configure wireless LAN settings by pressing ENTER

when "Start" is displayed.

0 This is displayed only when "On" is selected in "Wi-Fi".

0 Refer to Initial Setup (P12) for Wi-Fi settings.

SSID The SSID of the connected access point

Signal The signal strength of the connected access point

Stat The status of the connected access point

MAC Address This is the MAC address of this unit.

This value is specific to the component and cannot be changed.

DHCP "Enable (default value)": Auto configuration by DHCP

"Disable": Manual configuration without DHCP

If "Disable" is selected, you must set "IP Address", "Subnet

Mask", "Gateway", and "DNS Server" manually.

IP Address Displays/Sets the IP address.

Subnet Mask Displays/Sets the subnet mask.

Gateway Displays/Sets the gateway.

DNS Server Displays/Sets the primary DNS server.

Proxy URL Displays/Sets the proxy server URL.

Proxy Port Displays/Sets the proxy server port number when you enter

"Proxy URL".

SN29403238B_SX-N30AE_En.book 29 ページ２０１８年２月２８日　水曜日　午後５時０分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer SX-N30AE Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SX-N30AE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info