Bedienungsanleitung Pioneer SX-SW77 (Seite 30 von 156) (Englisch)

791723

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

Surround sound settings

Dynamic Range Control

When watching Dolby Digital or DTS material at low

volume, low level sounds—including some of the

dialog—can be difficult to hear properly. Using one of the

Dynamic Range Control (DRC) settings can help by

bringing up the low level sounds, while controlling high

level peaks.

1Press SHIFT+SYSTEM SETUP.

2Hold SHIFT and use the

/

buttons to select

DRC.

3Use SHIFT +

/

to select a setting.

Select one of the following:

•

DRC OFF

(default)

– No dynamic range adjustment

(use when listening at higher volume)

•

DRC MID

– Mid setting

•

DRC HIGH

– Dynamic range is reduced (loud sounds

are reduced in volume while quieter sounds are

increased)

4Press SHIFT+ENTER to exit.

Dual mono setting

Specifies how dual mono encoded Dolby Digital or DTS

soundtracks should be played. You can also use this

setting to switch the audio channel on DVD-RW discs

recorded with bilingual audio.

1Press SHIFT+SYSTEM SETUP.

2Hold SHIFT and use the

/

buttons to select

DRC.

3Use SHIFT +

/

to select a setting.

Select one of the following:

•

CH1 MONO

(default)

– Only channel 1 is played

•

CH2 MONO

– Only channel 2 is played

•

CH1/CH2

– Both channels are played through the

front speakers

4Press SHIFT+ENTER to exit.

Adjusting the channel levels using

the test tone

If you prefer, you can set the channel levels using a test

tone as a reference, rather than playing a source (see

Channel level setting

on page 29). A test tone is played

through each speaker in turn, allowing you to adjust the

level as it plays.

Note that the channel level settings for stereo sources

are independent of the settings for surround sound

sources.

1 Press SHIFT+SURROUND to select the Auto

listening mode.

• If you want to set the channel levels for stereo (two

channel) playback, select the

STEREO

listening

mode.

2Press SHIFT+TEST TONE.

The test tone is output from each speaker in turn.

3 While a test tone is playing, hold SHIFT and use

the

/

buttons to adjust that channel level.

The aim is to adjust the levels so that you hear the test

tone at the same volume from each speaker. You can

adjust the level of each channel by ± 10 dB.

•You can adjust the overall volume of test tone output

using the

VOLUME

+/– buttons (this does not affect

the channel level settings).

• Because of the ultra low frequencies the subwoofer

produces, it may sound quieter than it really is. We

suggest adjusting the subwoofer level using the

method described in

Channel level setting

page 29.

4 When you’re done, press SHIFT+ENTER to exit

test tone setup.

• If you use the Room Setup feature again, it will

overwrite the settings you have made here.

Note

1A similar adjustment feature is available on the DVD recorder—see

Audio DRC

on page 129.

2A similar adjustment feature is available on the DVD recorder—see

Switching audio channels

on page 99.

SX-SW77.book Page 30 Wednesday, April 27, 2005 6:05 PM

Downloaded from www.Manualslib.com manuals search engine

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer SX-SW77 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SX-SW77

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info