Bedienungsanleitung Pioneer VSA-AX10i-S (Seite 25 von 104) (Englisch)

574062

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

Connecting your equipment

Caution

• These speaker terminals can be under hazardous

voltage. When you connect or disconnect the speaker

cables, to prevent the risk of electric shock, do not

touch uninsulated parts before disconnecting the

power cord.

• Make sure that all the bare speaker wire is twisted

together and inserted fully into the speaker terminal.

If any of the bare speaker wire touches the back panel

it may cause the power to cut off as a safety measure.

Bare wire connections

Before you start connecting the speakers, make sure that

the speaker cable you’re going to use is properly

prepared with about 1 cm of insulator stripped from each

wire, and the exposed wire strands twisted together.

To connect a terminal, unscrew the terminal a few turns

until there is enough space to insert the exposed wire.

Once the wire is in position, tighten the terminal until the

wire is firmly clamped.

Note

• Please refer to the manual that came with your

speakers for details on how to connect the other end

of the speaker cables to your speakers.

• The speaker terminals on this amplifier can be

connected in a number of ways, depending on your

setup. See Speaker Systems on page 52 for an

overview of the possible configurations.

• Other connections on page 75 provides greater detail

on alternate speaker setups such as using speaker

system B (page 75), bi-surround (page 77), bi-amping

(page 76) and bi-wiring (page 77).

Placing the speakers

Where you put your speakers in the room has a big effect

on the quality of the sound. The following guidelines

should help you to get the best sound from your system.

(see also Optimizing your speaker setup on page 90).

• The subwoofer can be placed on the floor. Ideally, the

other speakers should be at about ear-level when

you’re listening to them. Putting the speakers on the

floor (except the subwoofer), or mounting them very

high on a wall is not recommended.

• For the best stereo effect, place the front speakers

2–2.5 m apart, at equal distance from the TV.

• Install the center speaker above or below the TV so

that the sound of the center channel is localized at

the TV screen.

• When placing speakers near the TV, use magnetically

shielded speakers to prevent possible interference,

such as discoloration of the picture when the TV is

switched on. If you do not have magnetically shielded

speakers and notice discoloration of the TV picture,

move the speakers farther away from the TV.

• If possible, install the surround speakers slightly

above ear level.

Caution

• Make sure that all speakers are securely installed.

This not only improves sound quality, but also

reduces the risk of damage or injury resulting from

speakers being knocked over or falling in the event of

external shocks such as earthquakes.

Front R

Front L

Surround

back R

Surround

Sub-

woofer

Center

Surround

back L

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSA-AX10i-S Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSA-AX10i-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info