Bedienungsanleitung Pioneer VSA-AX10i-S (Seite 52 von 104) (Englisch)

574062

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

The Surround Setup menu

• Speaker Systems – Specify the size and number of

speakers you’ve connected (page 52).

• Channel Level – Adjust the overall balance of your

speaker system (page 54).

• Speaker Distance – Specify the distance of your

speakers from the listening position (page 55).

• Acoustic Cal EQ – Adjust overall equalization

depending on your room characteristics (page 55).

• X-Curve – Adjust the amount of ‘re-equalization’

necessary to achieve a flat frequency response from

your home theater system (page 59).

5 Make the adjustments necessary for each

setting, pressing ENTER to confirm after each screen.

When you’re finished, you can check through your

settings screen by screen by selecting Check from the

Surround Setup menu (see Checking your surround

settings on page 60 for more on this).

Speaker Systems

You need to specify the number of speakers you have in

your system, and how you want to route the sound. It is a

good idea to make sure that the settings made in

Introduction to home theater on page 35 are correct.

1 Select ‘Speaker Systems’ then press ENTER.

2 Select how you want to set up your speakers

then press ENTER.

• Manual Free – Manually set all speakers.

• Manual THX – All speakers are set to SMALL. You

can only select the number of surround back

speakers.

• Auto – All speakers are set automatically. (The

microphone must be hooked up to the front panel to

do this.)

3 Specify how your speakers are configured.

Use / (cursor left/right) to cycle through the

following options:

• Normal Surround – Select for normal home theater

use.

• Front Bi-Amp – Select this setting if you’re bi-

amping your front speakers (see Bi-amping your front

speakers on page 76).

• Bi-Surround – Select if you’re using two sets of

surround speakers (see Adding a second set of

surround speakers for Bi-Surround on page 77).

If you selected Normal Surround, you’ll also have to

select the speaker system B setting:

• Second Zone – Select if you want to hear speaker

system B in a separate room.

• ITU-R – Select this setting to use two switchable

main speaker systems using speaker system B (see

Alternating surround speaker setups using speaker

system B (ITU-R) on page 76).

• OFF – Select if no speakers are connected to the B

terminals.

4 Press ENTER to go to the next screen.

• If you selected Auto in step 2, you will have to select

Next and then press ENTER to continue to the auto

(test tone) setup.

Select Start and press ENTER to start the test tones

when you’ve made sure the room is free of ambient noise.

Go to step 8 when you see OK appear on the OSD.

2.Surround Setup

[ Check ]

[ 1.Speaker Systems ]

[ 2.Channel Level ]

[ 3.Speaker Distance ]

[ 4.Acoustic Cal EQ ]

[ 5.X-Curve ]

[Return]

2.1. Speaker Systems

[Manual Free]

[Manual THX]

(all small)

[Auto]

[Return]

2.1.Speaker Systems

Manual Free

Speaker System Select

[Normal Surround ]

[ Second Zone ]

[ Next]

2.1.Speaker Systems

Manual Free

Speaker System Select

[Normal Surround ]

[ Second Zone ]

[ Next]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSA-AX10i-S Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSA-AX10i-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info