574062
73
Zoom out
Zoom in
Vorherige Seite
1/104
Nächste Seite
Using other functions
08
73
En
Checking your system settings
Use the status display screen to check the various
settings you’ve made for features such as sound delay,
digital noise reduction, and high-sampling.
1 From the remote control amplifier menu, press
STATUS to check the system settings.
You may need to press on the Home menu ( )
first before reaching the amplifier menu screen shown
below (use the / (cursor left/right) soft keys to go to
the previous/next menu screen).
These appear on both the OSD and the front panel
display.
The front panel display shows each of the following
settings for two seconds each:
Note
If the Stream Direct mode is switched on, some
settings above will show OFF, even though they are
switched on.
2 When you’re finished, press STATUS again to
switch off the display.
Resetting the system
Use this feature to reset the system to its factory default
settings (see Default amplifier settings below).
1 Switch the amplifier into standby.
2 While holding down the front panel DIGITAL NR
button, press and hold STANDBY/ON for about
three seconds.
The display shows RESET?.
3 Press the front panel OPTION + button.
The display shows OK?.
4 Within 5 seconds, press OPTION –.
The amplifier should now be reset.
Note
This doesn’t affect the presets that you have
programmed into the remote control (see Using the
remote control with other components on page 61).
See Resetting the remote control on page 10 to do
this.
Default amplifier settings
The table below shows the factory default settings. When
you reset the system, the amplifier reverts to these
defaults:
Surround back speaker/
Virtual back speaker
Video select
Acoustic calibration EQ Dual mono
Digital noise reduction Sound delay
Midnight Hi-bit
Loudness High-sampling
Tone Real phantom
AMPLIFIER
AMPLIFIER
3/3
SB CH
MODE
INPUT
STATUS
INPUT
AT T
SPEAKER
A/B
VIDEO
SELECT
TAPE2
MONITOR
DISPLAY
DIMMER
AMPLIFIER
TV
CONT
SB CH MODE :
ACOUS. CAL EQ :
DIGITAL NR :
MIDNIGHT :
LOUDNESS :
TONE CONTROL :
VIDEO SELECT :
DUAL MONO :
SOUND DELAY :
HI-BIT :
HI-SAMPLING :
REAL PHANTOM :
ALL ADJ
OFF
ON
DVD/LD
CH1
0.0frame
OFF
OFF
OFF
OFF
OFF
OFF
Setting type Default setting Page ref.
Input DVD/LD
Master volume – – – dB (no sound)
Listening mode STANDARD (video inputs,
multichannel inputs, USB)
STEREO (audio inputs)
page 39
Advanced surround
effect level
90 (5/7CH STEREO)
50 (all other modes)
page 41
Listening mode (w/
headphones)
STEREO page 42
Stream Direct mode SD:1 NORMAL (ON) page 43
Acoustic Calibration
EQ
OFF (switches to ALL CH ADJ
after the Auto Surround Setup)
page 44
Input signal select AUTO except multichannel
inputs (ANALOG) and USB
(DIGITAL)
page 44
USB / multichannel
input channel setting
8 channels page 45
Surround Back
Channel mode
ON (with surround back
speaker(s) connected)
page 46
Virtual Surround Back
mode
OFF page 47
Hi-bit/Hi-sampling OFF page 48
73

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Pioneer VSA-AX10i-S wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Pioneer VSA-AX10i-S

Pioneer VSA-AX10i-S Bedienungsanleitung - Deutsch - 104 seiten

Pioneer VSA-AX10i-S Bedienungsanleitung - Englisch - 25 seiten

Pioneer VSA-AX10i-S Bedienungsanleitung - Holländisch - 104 seiten

Pioneer VSA-AX10i-S Bedienungsanleitung - Französisch - 104 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info