Bedienungsanleitung Pioneer VSA-AX10i-S (Seite 76 von 104) (Englisch)

574062

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

Other connections

Alternating surround speaker setups using

speaker system B (ITU-R)

After you connect an alternate set of surround speakers,

you can use speaker system B to provide surround sound

when listening to sources like DVD-Audio discs. This will

give you a setup of 9 speakers where the front and center

speakers can be used with normal 7.1 surround (speaker

system A), or 5.1 surround with DVD-Audio sources

(speaker system B in ITU-R setting).

1 Connect an alternate (ITU-R) set of surround

speakers as shown below.

Connect the ITU-R surround left speaker to the left

speaker terminal of speaker system B. Connect the ITU-R

surround right speaker in the same way.

• Make sure that the + / – connections are properly

inserted (A and B speaker systems are opposite).

2 Select the ‘ITU-R’ setting from the Speaker

Systems menu.

See Speaker Systems on page 52 to specify how you’re

using speaker system B. Normal Surround should be

selected to make this setting.

3 Use the SPEAKER A/B button on the remote

control amplifier menu screen to select a speaker

system setting.

You can also use the SP SYSTEM A/B button on the front

panel.

Choose between the following settings (the shaded

boxes indicate the active speakers in each setup):

• SPA: Normal – Normal surround (for movies, etc.)

• SPB: ITU-R – ITU-R surround setup for DVD-Audio

and other multichannel music sources. See Speaker

system setup for DVD-Audio/multichannel music

sources on page 91 for more on this.

• SPOFF– No sound is output from the speakers.

Note

• Depending on the Stream Direct mode, the surround

channel signal(s) will be output from either the

surround, or surround back channel pre-outs when

SPB: ITU-R is selected.

Bi-amping your front speakers

Bi-amping is when you connect the high frequency driver

and low frequency driver of your speakers to different

amplifiers (in this case, to both front and surround back

terminals) for better crossover performance. Your

speakers must be bi-ampable to do this (having separate

terminals for high and low) and the sound improvement

will depend on the kind of speakers you’re using.

1 Connect your speakers as shown below.

This illustration below shows the connections for bi-

amping your front left speaker. Hook up your front right

speaker in the same way.

Since both front and surround back speaker terminals

output the same audio, it doesn’t matter which set (front

or surround back) is powering which part (Hi or Low) of

the speaker.

• Make sure that the + / – connections are properly

inserted. (A and B speaker systems are opposite).

FRONT

CENTER

SUR-

ROUND

SUR-

ROUND

BACK

(Single)

ITU-R surround

left speaker

ITU-R surround

right speaker

FRONT

CENTER

SUR-

ROUND

SUR-

ROUND

BACK

(Single)

Front left

speaker

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSA-AX10i-S Seite 76

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSA-AX10i-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info