Bedienungsanleitung Pioneer VSA-AX10i-S (Seite 92 von 104) (Englisch)

574062

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

Additional information

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with

this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other

components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks

listed below, contact the Pioneer Service Center specified on your warranty card.

Power

No sound

Symptom Cause Remedy

The power does not turn on. • The power plug is disconnected. • Connect the power plug to the wall outlet.

• The protection circuit may have been

activated.

• Disconnect the power plug from the outlet, and insert

again.

• Something is obstructing the rear panel fan. • Unplug the ampliﬁer from the wall and call the Pioneer

Service Center speciﬁed on your warranty card.

The ampliﬁer suddenly switches

off.

• The speaker wires are frayed or sticking out

of the jack, and are touching the back of the

ampliﬁer or another set of wires.

• Reinsert the speaker wires, making sure there are no

stray strands of wire and that they are inserted fully.

• The ampliﬁer has a serious problem. • Unplug the ampliﬁer from the wall and call the Pioneer

Service Center speciﬁed on your warranty card.

During loud playback the power

suddenly switches off.

• The protection circuit has been activated

because the lowest actual impedance of the

speakers (as opposed to the speakers rated

impedance) is dangerously low.

• Turn down the volume.

• When its convenient, go to Acoustic Calibration EQ on

page 55 and lower the 63 Hz and 125 Hz equalizer levels

using the manual setting.

• Turning the digital safety feature on may allow you to

turn up the volume a little more. To switch between

SAFETY 1 (medium effect), SAFETY 2 (more effect) and

SAFETY OFF, put theampliﬁer into standby, then press the

 STANDBY/ON button while holding down the OPTION

button on the front panel. If the power switches off even

with SAFETY 2 switched on, turn down the volume.

AMP ERR blinks in the display,

then the power automatically

switches off.

• The ampliﬁer has a serious problem. • After about a minute (you won’t be able to switch the

unit on during this time), switch the ampliﬁer back on. If

the message persists, call the Pioneer Service Center

speciﬁed on your warranty card.

FAN STOP blinks in the display,

then the power automatically

switches off.

• Something is obstructing the fan located on

the underside of the unit.

• Unplug the receiver from the wall and call the Pioneer

Service Center speciﬁed on your warranty card.

• The fan is malfunctioning. • Unplug the receiver from the wall and call the Pioneer

Service Center speciﬁed on your warranty card.

OVERHEAT blinks in the display

and no sound is output.

• The internal temperature of the unit has

become too high.

• After allowing the unit to cool down in a well-ventilated

place, try switching the ampliﬁer back on. Make sure you

follow the guidelines for improving heat dispersal in

Ventilation on page 2.

Symptom Cause Remedy

No sound is output when an

input source is selected.

• Improper connections. • Make sure you have properly connected the component

to the corresponding input on the back of the ampliﬁer

(see Connecting your equipment on page 12).

• Sound is muted or the volume is turned

down.

• Press MUTE or adjust the volume accordingly.

• The TAPE 2 monitoring feature is on. • Press TAPE 2 MONITOR to switch it off (see Monitoring

your recording on page 69).

• Speakers are turned off or selected

improperly with the SP SYSTEM A/B switch.

• Press SP SYSTEM A/B to select the proper speaker set

(see Switching the speaker system on page 75).

• The input signal type is incorrect. • Press SIGNAL SELECT to select the proper input signal

(see Selecting the input signal type on page 44).

• The i.LINK source selected for the main

room has also been selected as a source in

the sub room.

• Choose a different source or choose a different input

signal for the main room, such as DIGITAL or ANALOG

(see Selecting the input signal type on page 44).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSA-AX10i-S Seite 92

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSA-AX10i-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info