Bedienungsanleitung Pioneer VSX-1015TX (Seite 68 von 76) (Englisch)

574077

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Additional information

Other audio problems

No sound from one speaker. • The speaker setting has been set to NO.• Change the setting in Speaker Setting on page 46.

• The speaker level is too low. • Check the level in Channel Level on page 47.

• The speaker isn’t connected properly. • Check Connecting the speakers on page 20 to make sure

the speaker is connected correctly.

• The source has no sound output for that

channel.

• By choosing an advanced effect listening mode (see

Listening in surround sound on page 31), you may be able

to create an extra channel for the speaker.

Sound is produced from analog

components, but not from digital

ones (DVD, LD, CD-ROM etc.).

• The digital input assignment is wrong. • Assign the digital inputs correctly (see Assigning the

digital inputs on page 62).

• The digital components aren't connected

properly.

• Make sure you have properly connected the digital

component to the corresponding input on the back of the

receiver (see Connecting up on page 14).

• The player is not compatible with the source

you're using, or the player settings are

incorrect.

• Choose a compatible source, or check the component’s

manual for the correct settings.

• The digital output level has been turned

down on a CD recorder or other component

equipped with digital output level adjustment

capability.

• Set the digital volume level of the player to full, or to the

neutral position.

• The multichannel analog inputs are

selected.

• Press MULTI CH IN again (see Selecting the

multichannel analog inputs on page 39).

• The input signal type is set to ANALOG.• Set the input signal type to DIGITAL (see Choosing the

input signal on page 35).

No sound is output or a noise is

output when Dolby Digital/DTS

software is played back.

• A DVD player not compatible with Dolby

Digital/DTS is being used.

• Make sure your DVD player is compatible with Dolby

Digital/DTS.

• The settings on the DVD player are incorrect

and/or the DTS signal output is turned off.

• Make sure the player's settings are correct and/or the

DTS signal out is on. Refer to the instruction manual

supplied with the DVD player.

• The digital output level is turned down on a

CD player or other component equipped with

digital output level adjustment capability. (The

DTS signal has been altered by the player, and

cannot be read.)

• Set the digital volume level of the player to full, or to the

neutral position.

Symptom Cause Remedy

Broadcast stations cannot be

selected automatically, or there

seems to be considerable noise

in radio broadcasts.

FM broadcasts

• The FM antenna is not fully extended or is

poorly positioned.

• Fully extend the FM wire antenna, position for best

reception, and secure to a wall.

• Weak radio signals. • Connect an outdoor FM antenna (see page 19).

AM broadcasts

• The AM antenna is poorly positioned. • Adjust the direction and position for best reception.

• Weak radio signals. • Connect an additional internal or external AM antenna

(see page 19).

• Interference caused by other equipment

(ﬂuorescent lamp, motor, etc.).

• Turn off the equipment causing the noise or move it

away from the receiver.

• Place the antenna farther away from the equipment

causing the noise.

A multi channel DVD source

appears to be downmixed from 2

channels during playback.

• The source is coming from something other

than the MULTI CH IN jacks (for example,

digital PCM output, etc.)

• Check the MULTI CH IN connections (see Connecting

multichannel analog components on page 17) and select

the multichannel analog inputs with the MULTI CH IN

button (see Selecting the multichannel analog inputs on

page 39).

Noise is output when scanning a

DTS CD.

• The scan function performed by the player

slightly alters the digital information, making

it unreadable.

• This is not a malfunction, but be sure to turn the volume

down to prevent the output of loud noise from your

speakers.

When playing a DTS format LD

there is audible noise on the

soundtrack.

• The input signal type is set to ANALOG.• Set the input signal type to DIGITAL (see Choosing the

input signal on page 35).

VSX_1015.book.fm 68 ページ２００４年１２月９日　木曜日　午前１０時３６分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-1015TX Seite 68

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info