Bedienungsanleitung Pioneer VSX-1018AH-K (Seite 83 von 100) (Englisch)

455215

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

Additional information

Video

Settings

Symptom Remedy

No image is output when an

input is selected.

• Check the video connections of the source component (see page 18).

• For high-definition video (using component video connections), or when digital video conversion

is switched off (in Setting the Video options on page 72), you must connect your TV to this receiver

using the same type of video cable as you used to connect your video component.

• Make sure the input assignment is correct for components connected using component or HDMI

cables (see The Input Setup menu on page 67).

• Check the video output settings of the source component.

• Check that the video input you selected on your TV is correct.

• Some components (such as video game units) have resolutions that may not be converted. If

adjusting this receiver’s Resolution setting (in Setting the Video options on page 72) and/or the

resolution settings on your component or display doesn’t work, try switching Digital Video

Conversion (in Setting the Video options on page 72) OFF.

Can’t record video. • Check that the source is not copy-protected.

• The video converter is not available when making recordings. Check that the same type of video

cable is used for connecting both the recorder and the video source (the one you want to record) to

this receiver.

Noisy, intermittent, or distorted

picture.

• Sometimes a video deck may output a noisy video signal (during scanning, for example), or the

video quality may just be poor (with some video game units, for example). The picture quality may

also depend on the settings, etc. of your display device. Switch off the video converter and reconnect

the source and display device using the same type of connection (component or composite), then

start playback again.

Symptom Remedy

The Auto MCACC Setup

continually shows an error.

• The ambient noise level may be too high. Keep the noise level in the room as low as possible (see

also Problems when using the Auto MCACC Setup on page 11). If the noise level cannot be kept low

enough, you will have to set up the surround sound manually (page 41).

After using the Auto MCACC

Setup, the speaker size setting

is incorrect.

• There may have been some low frequency noise in the room from an air-conditioner, motor, etc.

Switch off all other appliances in the room and use Auto MCACC Setup again.

• Depending on a number of factors (room size, speaker placement, etc.) this may occur in some

cases. Change the speaker setting manually in Speaker Setting on page 48, and use the ALL (Keep

SP System) option for the Custom Menu in Automatic MCACC (Expert) on page 38 if this is a

recurring problem.

Can’t adjust the Fine Speaker

Distance setting (page 42)

properly.

• Check that the speakers are all in phase (make sure the positive (+) and negative (–) terminals are

matched up properly).

The display shows KEY LOCK

ON when you try to make

settings.

• With the receiver in standby, press  STANDBY/ON while holding down the SPEAKERS button to

disable the key lock.

Most recent settings have been

erased.

• The power cord was disconnected from the wall while adjusting this setting.

VSX-1018AH_KU.book Page 83 Monday, March 10, 2008 4:51 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-1018AH-K Seite 83

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-1018AH-K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info